7 open source boards using the YAAJ_WeAct_BlackPill_Part_Like

Real designs built with the YAAJ_WeAct_BlackPill_Part_Like, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the YAAJ_WeAct_BlackPill_Part_Like

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the YAAJ_WeAct_BlackPill_Part_Like connects to, and the resistors, capacitors and other passives placed on it.

  • The PA11 pin is left unconnected on 6 of 6 designs.
  • The PA12 pin is left unconnected on 6 of 6 designs.
  • The VBAT pin is left unconnected on 6 of 6 designs.
  • The PC13 pin is left unconnected on 6 of 6 designs.
PA11pin 8Connected to: Not connected 100%
PA12pin 9Connected to: Not connected 100%
PB3pin 11Connected to: Signal 100%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
PB4pin 12Connected to: Signal 100%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
5Vpin 18, 40Connected to: Not connected 67% · 5V 33%
GNDpin 19, 39Connected to: GND 92%
3V3pin 20, 38Connected to: 3.3V 67% · not connected 33%
VBATpin 21Connected to: Not connected 100%
PC13pin 22Connected to: Not connected 100%
PC14pin 23Connected to: Not connected 67% · a signal 33%
  • Pull-up to 3.3V on 33%
PC15pin 24Connected to: Not connected 100%
RESpin 25Connected to: Not connected 100%
PB2pin 36Connected to: Not connected 67% · a signal 33%

24 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Auxiliary board by reubenstr, Kebu by Cedutus, Yuki by crolbar and Keyther by MagoSaronno.

The YAAJ_WeAct_BlackPill_Part_Like in open source designs

The gallery holds 7 open source boards using the YAAJ_WeAct_BlackPill_Part_Like from 7 GitHub repositories; a typical one measures about 141.6 × 89.6 mm and carries around 31 components.

100% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.

The most starred is Auxiliary board by reubenstr.

Parts used alongside the YAAJ_WeAct_BlackPill_Part_Like

Microcontrollers on boards using the YAAJ_WeAct_BlackPill_Part_Like

What boards using the YAAJ_WeAct_BlackPill_Part_Like are built for

YAAJ_WeAct_BlackPill_Part_Like: common questions

Where can I find a YAAJ_WeAct_BlackPill_Part_Like reference design?

Each of the 7 boards on this page is a real design using the YAAJ_WeAct_BlackPill_Part_Like. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the YAAJ_WeAct_BlackPill_Part_Like PA11 pin connected?

The PA11 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the YAAJ_WeAct_BlackPill_Part_Like.

How is the YAAJ_WeAct_BlackPill_Part_Like PA12 pin connected?

The PA12 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the YAAJ_WeAct_BlackPill_Part_Like.

How is the YAAJ_WeAct_BlackPill_Part_Like VBAT pin connected?

The VBAT pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the YAAJ_WeAct_BlackPill_Part_Like.

Which microcontrollers do boards using the YAAJ_WeAct_BlackPill_Part_Like use?

Most are built on Raspberry Pi (2) and ESP32 (1).

How big is a typical board using the YAAJ_WeAct_BlackPill_Part_Like?

The median is 141.6 × 89.6 mm, and 100% are two-layer designs.

What is the most popular open source board using the YAAJ_WeAct_BlackPill_Part_Like?

By GitHub stars, Auxiliary board by reubenstr, with 242 stars.

Can I simulate one of these boards using the YAAJ_WeAct_BlackPill_Part_Like before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part