8 open source boards using the 74HC2G17GW
Real designs built with the 74HC2G17GW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Sitina 1 Sensor Board
CameraNexus
71.5 × 63.6 mm415 parts6LMIT73STM32
Proteus
mck1117
135 × 82.5 mm348 parts4LNo license50STM32
Polygonus
FOME-Tech
103 × 82.4 mm299 parts4LNo license21FPGA
Sitina 1 Sensor Board
novvoo
71.5 × 63.6 mm415 parts6LMIT2AVR/Arduino
Cpl adc board
matham
101.6 × 50.8 mm74 parts4LNo license1STM32
Fome mc
halbritt
162 × 115 mm462 parts4LNo license0STM32
Wideband controller
rusefi
54.1 × 65.8 mm129 parts4LNo license48VR-Hall
rusefi
49 × 52 mm52 parts2LNo license48
How designs wire the 74HC2G17GW
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the 74HC2G17GW connects to, and the resistors, capacitors and other passives placed on it.
- The 1A pin has a series resistor on 4 of 7 designs, most often 2.7 kΩ (then 4.7 kΩ).
- The 1A pin has a capacitor to GND on 4 of 7 designs, most often 1 nF.
- The 2A pin has a capacitor to GND on 4 of 7 designs, most often 1 nF.
- The 2A pin has a series resistor on 4 of 7 designs, most often 2.7 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1Apin 1 | Connected to: SRV05-4 43% |
|
| GNDpin 2 | Connected to: GND 71% · 3.5V 29% | — |
| 2Apin 3 | Connected to: SRV05-4 43% |
|
| VCCpin 5 | Connected to: 5V 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sitina 1 Sensor Board by CameraNexus, Proteus by mck1117, VR-Hall by rusefi and Polygonus by FOME-Tech.
The 74HC2G17GW in open source designs
The gallery holds 8 open source boards using the 74HC2G17GW from 7 GitHub repositories; a typical one measures about 86.5 × 64.7 mm and carries around 324 components.
88% use four copper layers or more, and 25% carry an open source license.
The most starred is Sitina 1 Sensor Board by CameraNexus.
Parts used alongside the 74HC2G17GW
Microcontrollers on boards using the 74HC2G17GW
What boards using the 74HC2G17GW are built for
74HC2G17GW: common questions
Where can I find a 74HC2G17GW reference design?
Each of the 8 boards on this page is a real design using the 74HC2G17GW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 74HC2G17GW 1A pin?
The 1A pin has a series resistor on 4 of 7 designs, most often 2.7 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the 74HC2G17GW.
How is the 74HC2G17GW 2A pin connected?
The 2A pin has a capacitor to GND on 4 of 7 designs, most often 1 nF. Counted from the KiCad layouts of 7 open source designs using the 74HC2G17GW.
What decoupling capacitors do designs use on the 74HC2G17GW VCC pin?
The VCC pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the 74HC2G17GW.
What parts are used alongside the 74HC2G17GW?
The REF3033, LMR14020, LPS25HB, MCP6004T-I/ST and SRV05-4 appear in the most repositories here.
Which microcontrollers do boards using the 74HC2G17GW use?
Most are built on STM32 (4), FPGA (2) and AVR/Arduino (1).
How big is a typical board using the 74HC2G17GW?
The median is 86.5 × 64.7 mm, and 13% are two-layer designs.
What is the most popular open source board using the 74HC2G17GW?
By GitHub stars, Sitina 1 Sensor Board by CameraNexus, with 73 stars.
Can I simulate one of these boards using the 74HC2G17GW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.