13 open source boards using the MCP6004T-I/ST
Real designs built with the MCP6004T-I/ST, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Micro rusEFI
rusefi
80.6 × 93.7 mm238 parts2LNo license98STM32
Proteus
mck1117
135 × 82.5 mm348 parts4LNo license50STM32
Polygonus
FOME-Tech
103 × 82.4 mm299 parts4LNo license21ESP32
Glove v4-routing candidate
latintzar
100 × 80 mm561 parts8LMIT0STM32
Fome mc
halbritt
162 × 115 mm462 parts4LNo license0STM32
Output.Panel R0.5.1 300x300 2layer step1 Modified
rusefi
267 × 300 mm235 parts2LNo license98ESP32
Glove v4-placement
latintzar
100 × 80 mm560 parts6LMIT0STM32
Output.Panel R0.5.1 300x300 2layer step1 Modified 1and5 only
rusefi
18.8 × 17.8 mm235 parts2LNo license98Min evolver
FYNCH-BIO
109.2 × 64.5 mm68 parts4LNo license12Nordic nRF
Glove v3-routed
latintzar
90 × 60 mm356 parts4LMIT0STM32
Panel R0.5.1 300x300 2layer step1
rusefi
267 × 300 mm235 parts2LNo license98Nordic nRF
Glove v3-floorplan
latintzar
70 × 46 mm333 parts4LMIT0Nordic nRF
Glove v3-grouped
latintzar
90 × 60 mm330 parts4LMIT0
How designs wire the MCP6004T-I/ST
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MCP6004T-I/ST connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 6 designs, most often 470 kΩ (then 12 kΩ).
- The - pins have a series resistor on 6 of 6 designs, most often 100 kΩ (then 470 kΩ).
- Pin 14 has a series resistor on 6 of 6 designs, most often 470 kΩ (then 12 kΩ).
- The V- pin is tied to GND on 6 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6, 9, 13 | Connected to: The microcontroller 25% |
|
| +pin 3, 5, 10, 12 | Connected to: Signal 100% |
|
| V+pin 4 | Connected to: 3.3V 83% · a signal 17% |
|
| Pin 7 | Connected to: The microcontroller 50% |
|
| Pin 8 | Connected to: The microcontroller 50% |
|
| V-pin 11 | Connected to: GND 100% | — |
| Pin 14 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Micro rusEFI by rusefi, Proteus by mck1117, Polygonus by FOME-Tech and Min evolver by FYNCH-BIO.
The MCP6004T-I/ST in open source designs
The gallery holds 13 open source boards using the MCP6004T-I/ST from 6 GitHub repositories; a typical one measures about 100 × 80 mm and carries around 330 components.
69% use four copper layers or more, and 38% carry an open source license.
The most starred is Micro rusEFI by rusefi.
Parts used alongside the MCP6004T-I/ST
Microcontrollers on boards using the MCP6004T-I/ST
What boards using the MCP6004T-I/ST are built for
MCP6004T-I/ST: common questions
Where can I find a MCP6004T-I/ST reference design?
Each of the 13 boards on this page is a real design using the MCP6004T-I/ST. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP6004T-I/ST pin 1?
Pin 1 has a series resistor on 6 of 6 designs, most often 470 kΩ (then 12 kΩ). Counted from the KiCad layouts of 6 open source designs using the MCP6004T-I/ST.
What resistor goes on the MCP6004T-I/ST - pin?
The - pins have a series resistor on 6 of 6 designs, most often 100 kΩ (then 470 kΩ). Counted from the KiCad layouts of 6 open source designs using the MCP6004T-I/ST.
What resistor goes on the MCP6004T-I/ST pin 14?
Pin 14 has a series resistor on 6 of 6 designs, most often 470 kΩ (then 12 kΩ). Counted from the KiCad layouts of 6 open source designs using the MCP6004T-I/ST.
What parts are used alongside the MCP6004T-I/ST?
The 74HC2G17GW, LMR14020, LPS25HB, REF3033 and SRV05-4 appear in the most repositories here.
Which microcontrollers do boards using the MCP6004T-I/ST use?
Most are built on STM32 (7), Nordic nRF (3) and ESP32 (2).
How big is a typical board using the MCP6004T-I/ST?
The median is 100 × 80 mm, and 31% are two-layer designs.
What is the most popular open source board using the MCP6004T-I/ST?
By GitHub stars, Micro rusEFI by rusefi, with 98 stars.
Can I simulate one of these boards using the MCP6004T-I/ST before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.