12 open source boards using the ADS1115IDGST
Real designs built with the ADS1115IDGST, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Psu ext hardware
PSU-Ext-Org
100 × 50 mm110 parts4LCERN-OHL-S-2.07ESP32
WellD
kinggh0stee
100 × 55 mm99 parts2LMIT2RP2040/RP2350
Core micro surface
zeerolux
230 × 153 mm140 parts2LNo license1ESP32
PranRakshak
SrivarsanK
52 × 88 mm45 parts2LNo license1Technikerarbeit2026-hardwarepruefadapter
CodeByMika
416 × 130 mm436 parts4LNo license0STM32
OscilloBP Monitor
phantranthehuy
95 × 99 mm51 parts2LMIT0RP2040/RP2350
Core micro surface nohotswap
zeerolux
230 × 153 mm140 parts2LNo license1Softgalaxy Pi HAT 2v0
hsclouds
69.1 × 60.8 mm57 parts2LNo license1Design
beauforr
61 × 35 mm65 parts2LNo license0Adafruit ADS1115 16Bit I2C ADC
phantranthehuy
27.9 × 17.2 mm10 parts2LMIT0- schematic only · 81 partsESP32
ReefVolt SensorBuddy
blueacro
81 parts4LCERN-OHL-P-2.00 - schematic only · 59 partsSTM32
ProPrj ADC读取 2025-05-24
shydql
59 parts2LGPL-3.00
How designs wire the ADS1115IDGST
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ADS1115IDGST connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The SCL pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The VDD pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF (then 22 µF).
- The AIN0 pin has a series resistor on 4 of 7 designs, most often 1 kΩ (then 12 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3 | Connected to: GND 100% | — |
| AIN0pin 4 | Connected to: Signal 100% |
|
| AIN1pin 5 | Connected to: Signal 100% |
|
| VDDpin 8 | Connected to: 3.3V 57% · a signal 43% |
|
| SDApin 9 | Connected to: A connector 43%, the microcontroller 29% |
|
| SCLpin 10 | Connected to: A connector 43%, the microcontroller 29% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Psu ext hardware by PSU-Ext-Org, Softgalaxy Pi HAT 2v0 by hsclouds, PranRakshak by SrivarsanK and Core micro surface by zeerolux.
The ADS1115IDGST in open source designs
The gallery holds 12 open source boards using the ADS1115IDGST from 10 GitHub repositories; a typical one measures about 97.5 × 74.4 mm and carries around 73 components.
75% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Psu ext hardware by PSU-Ext-Org.
Parts used alongside the ADS1115IDGST
Microcontrollers on boards using the ADS1115IDGST
What boards using the ADS1115IDGST are built for
ADS1115IDGST: common questions
Where can I find a ADS1115IDGST reference design?
Each of the 12 boards on this page is a real design using the ADS1115IDGST. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ADS1115IDGST SDA pin?
The SDA pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the ADS1115IDGST.
What pull-up resistor is used on the ADS1115IDGST SCL pin?
The SCL pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the ADS1115IDGST.
What decoupling capacitors do designs use on the ADS1115IDGST VDD pin?
The VDD pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 7 open source designs using the ADS1115IDGST.
Which microcontrollers do boards using the ADS1115IDGST use?
Most are built on ESP32 (4), RP2040/RP2350 (2) and STM32 (2).
How big is a typical board using the ADS1115IDGST?
The median is 97.5 × 74.4 mm, and 75% are two-layer designs.
What is the most popular open source board using the ADS1115IDGST?
By GitHub stars, Psu ext hardware by PSU-Ext-Org, with 7 stars.
Can I simulate one of these boards using the ADS1115IDGST before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.