13 open source boards using the AT24CS32-SSHM
Real designs built with the AT24CS32-SSHM, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RPi-HAT-RGBW-LED-Controller
mikelawrence
65 × 56 mm54 parts2LMIT9RPi-Hat-Thermocouple
mikelawrence
65 × 56 mm40 parts2LMIT9Whole
Benedikt3141
109 × 55.5 mm83 parts2LMIT1AVR/Arduino
RadHardSchematics
FraserD404
203 × 79.7 mm34 parts2LNo license0STM32
THCAD-reader+Digital-IO
MetalMusings
112.5 × 65.6 mm135 parts2LNo license93PlantWatering PCB02
Benedikt3141
109 × 55.5 mm43 parts2LMIT1AVR/Arduino
Master Off V0.2
carloslcor
43 × 46 mm34 parts2LNo license0STM32
EaserCAT-7000
MetalMusings
112.5 × 65.6 mm134 parts2LNo license93STM32
Cyclometer v1
Vaaarad07
58.8 × 94 mm81 parts2LMIT10STM32
Ethercat stm32
MetalMusings
89.9 × 59.2 mm134 parts4LNo license93Ds3231
risejohan
38 × 28.6 mm13 parts2LNo license17STM32
THCAD-reader
MetalMusings
89.2 × 58.9 mm123 parts2LNo license938In-8Out-LAN9252-only
MetalMusings
89.2 × 58.9 mm95 parts2LNo license93
How designs wire the AT24CS32-SSHM
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the AT24CS32-SSHM connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 5 of 8 designs, most often 4.7 kΩ (then 3.9 kΩ).
- The SCL pin has a pull-up to 3.3V on 5 of 8 designs, most often 4.7 kΩ (then 3.9 kΩ).
- The A0 pin is tied to GND on 5 of 8 designs (a signal on 2).
- The A1 pin is tied to GND on 5 of 8 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 63% · a signal 25% | — |
| A1pin 2 | Connected to: GND 63% · a signal 25% | — |
| A2pin 3 | Connected to: GND 63% · a signal 25% | — |
| GNDpin 4 | Connected to: GND 88% | — |
| SDApin 5 | Connected to: A connector 38%, the microcontroller 25% |
|
| SCLpin 6 | Connected to: A connector 38%, the microcontroller 25% |
|
| WPpin 7 | Connected to: GND 63% · a signal 38% | — |
| VCCpin 8 | Connected to: 3.3V 88% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 8In-8Out-LAN9252-only by MetalMusings, Ds3231 by risejohan, Cyclometer v1 by Vaaarad07 and RPi-HAT-RGBW-LED-Controller by mikelawrence.
The AT24CS32-SSHM in open source designs
The gallery holds 13 open source boards using the AT24CS32-SSHM from 8 GitHub repositories; a typical one measures about 89.2 × 58.9 mm and carries around 81 components.
92% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is THCAD-reader+Digital-IO by MetalMusings.
Parts used alongside the AT24CS32-SSHM
Microcontrollers on boards using the AT24CS32-SSHM
What boards using the AT24CS32-SSHM are built for
AT24CS32-SSHM: common questions
Where can I find a AT24CS32-SSHM reference design?
Each of the 13 boards on this page is a real design using the AT24CS32-SSHM. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the AT24CS32-SSHM SDA pin?
The SDA pin has a pull-up to 3.3V on 5 of 8 designs, most often 4.7 kΩ (then 3.9 kΩ). Counted from the KiCad layouts of 8 open source designs using the AT24CS32-SSHM.
What pull-up resistor is used on the AT24CS32-SSHM SCL pin?
The SCL pin has a pull-up to 3.3V on 5 of 8 designs, most often 4.7 kΩ (then 3.9 kΩ). Counted from the KiCad layouts of 8 open source designs using the AT24CS32-SSHM.
How is the AT24CS32-SSHM A0 pin connected?
The A0 pin is tied to GND on 5 of 8 designs (a signal on 2). Counted from the KiCad layouts of 8 open source designs using the AT24CS32-SSHM.
Which microcontrollers do boards using the AT24CS32-SSHM use?
Most are built on STM32 (5) and AVR/Arduino (2).
How big is a typical board using the AT24CS32-SSHM?
The median is 89.2 × 58.9 mm, and 92% are two-layer designs.
What is the most popular open source board using the AT24CS32-SSHM?
By GitHub stars, THCAD-reader+Digital-IO by MetalMusings, with 93 stars.
Can I simulate one of these boards using the AT24CS32-SSHM before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.