9 open source boards using the ATECC508A
Real designs built with the ATECC508A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
LICSTER
thainnos
68.6 × 53.3 mm72 parts2LMIT122Breakpanel
monero-project
145 × 165 mm105 parts2LCERN-OHL-1.2115ESP32
Wifistepper
goodrobotics
77.6 × 57.3 mm85 parts4LNo license29AVR/Arduino
Badge2016
cryptovillage
76.2 × 76.2 mm43 parts2LNo license12STM32
Nitrokey Pro
Nitrokey
21.8 × 16.3 mm39 partsNo license5Pmod crypto
fm4dd
41 × 20.3 mm11 parts2LCERN-OHL-1.21STM32
Main
vives-projectwerk-2021
80 × 70 mm64 parts4LNo license0Breakneck
monero-project
53.3 × 64 mm89 parts2LCERN-OHL-1.2115NeOsensor-LoRaWANV2
fthiebolt
49.5 × 49.5 mm26 parts2LNo license5
How designs wire the ATECC508A
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ATECC508A connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 1 µF).
- The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 3.9 kΩ (then 2.2 kΩ).
- The SDL pin has a pull-up to 3.3V on 5 of 7 designs, most often 3.9 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 2, 3, 7 | Connected to: Not connected 100% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: The microcontroller 43%, a connector 29% |
|
| SDLpin 6 | Connected to: The microcontroller 43%, a connector 29% |
|
| VCCpin 8 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LICSTER by thainnos, Breakneck by monero-project, Wifistepper by goodrobotics and Badge2016 by cryptovillage.
The ATECC508A in open source designs
The gallery holds 9 open source boards using the ATECC508A from 8 GitHub repositories; a typical one measures about 68.6 × 57.3 mm and carries around 64 components.
75% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is LICSTER by thainnos.
Microcontrollers on boards using the ATECC508A
What boards using the ATECC508A are built for
ATECC508A: common questions
Where can I find a ATECC508A reference design?
Each of the 9 boards on this page is a real design using the ATECC508A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATECC508A VCC pin?
The VCC pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 7 open source designs using the ATECC508A.
What pull-up resistor is used on the ATECC508A SDA pin?
The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 3.9 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 7 open source designs using the ATECC508A.
What pull-up resistor is used on the ATECC508A SDL pin?
The SDL pin has a pull-up to 3.3V on 5 of 7 designs, most often 3.9 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 7 open source designs using the ATECC508A.
Which microcontrollers do boards using the ATECC508A use?
Most are built on AVR/Arduino (2), STM32 (2) and ESP32 (1).
How big is a typical board using the ATECC508A?
The median is 68.6 × 57.3 mm, and 75% are two-layer designs.
What is the most popular open source board using the ATECC508A?
By GitHub stars, LICSTER by thainnos, with 122 stars.
Can I simulate one of these boards using the ATECC508A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.