8 open source boards using the ATECC608A-MAHDA
Real designs built with the ATECC608A-MAHDA, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Diva card
diva-eng
85.4 × 53.7 mm92 parts2LMIT4Require
facethesouth
68 × 26 mm180 parts6LGPL-3.03ESP32
Com4bbb
eurovibes
54.6 × 86.4 mm61 parts4LCERN-OHL-S-2.00STM32
Verakey
Veracles-Hackclub
59 × 20 mm26 parts2LNo license0Raspberry Pi
CM4Card
will127534
64.6 × 44 mm54 parts4LMIT95Raspberry Pi
AP3100
imagestream
186 × 226 mm181 parts4LMIT1Raspberry Pi
AP3000
imagestream
186 × 226 mm175 parts4LMIT1Raspberry Pi
AP2000
imagestream
108 × 110 mm147 parts4LMIT1
How designs wire the ATECC608A-MAHDA
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATECC608A-MAHDA connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 4 of 6 designs, most often 4.7 kΩ (then 1 kΩ).
- The SCL pin has a pull-up to 3.3V on 4 of 6 designs, most often 4.7 kΩ (then 1 kΩ).
- The VCC pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 2, 3, 7 | Connected to: Not connected 100% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: The microcontroller 33% |
|
| SCLpin 6 | Connected to: The microcontroller 33% |
|
| VCCpin 8 | Connected to: 3.3V 100% |
|
| EPpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CM4Card by will127534, Diva card by diva-eng, Require by facethesouth and AP2000 by imagestream.
The ATECC608A-MAHDA in open source designs
The gallery holds 8 open source boards using the ATECC608A-MAHDA from 6 GitHub repositories; a typical one measures about 76.7 × 70 mm and carries around 120 components.
75% use four copper layers or more, and 88% carry an open source license.
The most starred is CM4Card by will127534.
Parts used alongside the ATECC608A-MAHDA
Microcontrollers on boards using the ATECC608A-MAHDA
What boards using the ATECC608A-MAHDA are built for
ATECC608A-MAHDA: common questions
Where can I find a ATECC608A-MAHDA reference design?
Each of the 8 boards on this page is a real design using the ATECC608A-MAHDA. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ATECC608A-MAHDA SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 6 designs, most often 4.7 kΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the ATECC608A-MAHDA.
What pull-up resistor is used on the ATECC608A-MAHDA SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 6 designs, most often 4.7 kΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the ATECC608A-MAHDA.
What decoupling capacitors do designs use on the ATECC608A-MAHDA VCC pin?
The VCC pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the ATECC608A-MAHDA.
Which microcontrollers do boards using the ATECC608A-MAHDA use?
Most are built on Raspberry Pi (4), ESP32 (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the ATECC608A-MAHDA?
The median is 76.7 × 70 mm, and 25% are two-layer designs.
What is the most popular open source board using the ATECC608A-MAHDA?
By GitHub stars, CM4Card by will127534, with 95 stars.
Can I simulate one of these boards using the ATECC608A-MAHDA before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.