10 open source boards using the ATECC608A-SSHDA
Real designs built with the ATECC608A-SSHDA, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Cable link
CableClub
36 × 46 mm40 parts4LApache-2.05Arduino UNO Experimental Shield
ffich
68.6 × 53.3 mm68 parts4LMIT4ATECC608A-Croquette
ElectronicCats
26.7 × 22.8 mm6 parts2LGPL-3.04STM32
Daveecu2
miata-bot
160 × 117.5 mm223 parts4LNo license3Bluepill Carrier
ffich
81.3 × 86.4 mm83 parts4LMIT1STM32
Ambient pcb dkaiot
LEAT-EDGE
73 × 77.5 mm166 parts2LCERN-OHL-P-2.00STM32
Stm32c071 embedded board
ondrejjel
60 × 60 mm49 parts4LMIT0ESP32
Fluxguard
lizuyi-6
52 × 29 mm34 parts4LNo license0Mspm0g3507-evm
Naveens-Lab
56 × 34.3 mm29 parts2LNo license0ESP32
Satellite SoM
inoa-io
56 × 30.4 mm17 parts2LCERN-OHL-P-2.02
How designs wire the ATECC608A-SSHDA
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the ATECC608A-SSHDA connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The SCL pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 2.2 kΩ).
- The VCC pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 2, 3, 7 | Connected to: Not connected 100% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: The microcontroller 44%, a connector 44%, TMP102XXDRL 22% |
|
| SCLpin 6 | Connected to: The microcontroller 44%, a connector 44%, TMP102XXDRL 22% |
|
| VCCpin 8 | Connected to: 3.3V 89% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Cable link by CableClub, ATECC608A-Croquette by ElectronicCats, Arduino UNO Experimental Shield by ffich and Daveecu2 by miata-bot.
The ATECC608A-SSHDA in open source designs
The gallery holds 10 open source boards using the ATECC608A-SSHDA from 10 GitHub repositories; a typical one measures about 58 × 49.7 mm and carries around 45 components.
60% use four copper layers or more, and 70% carry an open source license.
The most starred is Cable link by CableClub.
Parts used alongside the ATECC608A-SSHDA
Microcontrollers on boards using the ATECC608A-SSHDA
What boards using the ATECC608A-SSHDA are built for
ATECC608A-SSHDA: common questions
Where can I find a ATECC608A-SSHDA reference design?
Each of the 10 boards on this page is a real design using the ATECC608A-SSHDA. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ATECC608A-SSHDA SDA pin?
The SDA pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the ATECC608A-SSHDA.
What pull-up resistor is used on the ATECC608A-SSHDA SCL pin?
The SCL pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the ATECC608A-SSHDA.
What decoupling capacitors do designs use on the ATECC608A-SSHDA VCC pin?
The VCC pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF. Counted from the KiCad layouts of 9 open source designs using the ATECC608A-SSHDA.
What parts are used alongside the ATECC608A-SSHDA?
The CH340N, TJA1051T-3, AMS1117-3.3, TMP102XXDRL and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the ATECC608A-SSHDA use?
Most are built on STM32 (3), ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the ATECC608A-SSHDA?
The median is 58 × 49.7 mm, and 40% are two-layer designs.
What is the most popular open source board using the ATECC608A-SSHDA?
By GitHub stars, Cable link by CableClub, with 5 stars.
Can I simulate one of these boards using the ATECC608A-SSHDA before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.