9 open source boards using the AW9523B
Real designs built with the AW9523B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Printalyzer - Main Board
dektronics
188 × 110 mm136 parts4LNo license37ESP32
ILI9341 ESP32 GBC
theBrutzler
70 × 122.3 mm111 parts2LNo license9WEASEL
joebmz98
335 × 200 mm216 parts2LMIT3Makerspace badge
DanNixon
67.9 × 53.2 mm74 parts2LCERN-OHL-P-2.03ESP32
NosClock
hulakov
144 × 60 mm103 parts2LNo license1I2c led
lbthomsen
22.9 × 14 mm12 parts4LCustom license1DSP-Regulator-RevC
Phil-CIA
100 × 125 mm226 parts2LNo license0GBC CARD
theBrutzler
57.2 × 24 mm19 parts2LNo license9WEASEL KiCad MainBoard
joebmz98
335 × 200 mm216 parts2LMIT3
How designs wire the AW9523B
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the AW9523B connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 6 of 7 designs, most often 1 µF (then 4.7 µF).
- The SCL pin has a pull-up to 3.3V on 5 of 7 designs, most often 4.7 kΩ (then 2 kΩ).
- The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 4.7 kΩ (then 2 kΩ).
- The RST pin has a pull-up to 3.3V on 5 of 7 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 9, 25 | Connected to: GND 100% | — |
| AD0pin 18 | Connected to: GND 71% | — |
| SCLpin 19 | Connected to: A connector 71%, AW9523B 43%, the microcontroller 29% |
|
| SDApin 20 | Connected to: A connector 71%, AW9523B 43%, the microcontroller 29% |
|
| VCCpin 21 | Connected to: 3.3V 71% · a signal 29% |
|
| RSTpin 23 | Connected to: Signal 86% |
|
18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Printalyzer - Main Board by dektronics, GBC CARD by theBrutzler, Makerspace badge by DanNixon and WEASEL KiCad by joebmz98.
The AW9523B in open source designs
The gallery holds 9 open source boards using the AW9523B from 7 GitHub repositories; a typical one measures about 100 × 110 mm and carries around 111 components.
78% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Printalyzer - Main Board by dektronics.
What boards using the AW9523B are built for
AW9523B: common questions
Where can I find a AW9523B reference design?
Each of the 9 boards on this page is a real design using the AW9523B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the AW9523B VCC pin?
The VCC pin has a decoupling capacitor on 6 of 7 designs, most often 1 µF (then 4.7 µF). Counted from the KiCad layouts of 7 open source designs using the AW9523B.
What pull-up resistor is used on the AW9523B SCL pin?
The SCL pin has a pull-up to 3.3V on 5 of 7 designs, most often 4.7 kΩ (then 2 kΩ). Counted from the KiCad layouts of 7 open source designs using the AW9523B.
What pull-up resistor is used on the AW9523B SDA pin?
The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 4.7 kΩ (then 2 kΩ). Counted from the KiCad layouts of 7 open source designs using the AW9523B.
Which microcontrollers do boards using the AW9523B use?
Most are built on ESP32 (2) and STM32 (1).
How big is a typical board using the AW9523B?
The median is 100 × 110 mm, and 78% are two-layer designs.
What is the most popular open source board using the AW9523B?
By GitHub stars, Printalyzer - Main Board by dektronics, with 37 stars.
Can I simulate one of these boards using the AW9523B before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.