7 open source boards using the CCS811
Real designs built with the CCS811, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
- schematic only · 41 partsAVR/Arduino
FumeBot
ajithcodesit
41 partsMIT4 Whole
Benedikt3141
109 × 55.5 mm83 parts2LMIT1AVR/Arduino
Rf room sensor hw
dselcan
50.8 × 44 mm32 parts2LBSD-3-Clause0ESP32
Bussysteme und-Sensorik-ESP32-Projekt
SFMonsun
111.7 × 63.8 mm32 parts4LNo license0PlantWatering PCB02
Benedikt3141
109 × 55.5 mm43 parts2LMIT1Environmental-Sensors
basilfx
20.3 × 18 mm12 parts2LCC-BY-NC-4.024ESP32
ESP DEV BOARD
hamayanShowa-ele
76 × 92 mm42 parts2LNo license0
How designs wire the CCS811
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the CCS811 connects to, and the resistors, capacitors and other passives placed on it.
- The RESET pin has a pull-up to 3.3V on 5 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 4 of 4 designs, most often 4.7 kΩ (then 10 kΩ).
- The ADDR pin is tied to GND on 3 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADDRpin 1 | Connected to: GND 60% · 3.3V 20% · a signal 20% | — |
| RESETpin 2 | Connected to: Signal 100% |
|
| INTpin 3 | Connected to: Signal 80% · not connected 20% |
|
| VDDpin 6 | Connected to: 3.3V 80% · not connected 20% |
|
| WAKEpin 7 | Connected to: GND 60% · not connected 20% · a signal 20% | — |
| SDApin 9 | Connected to: Signal 80% · not connected 20% |
|
| SCLpin 10 | Connected to: Signal 100% |
|
| GNDpin 11 | Connected to: GND 100% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Environmental-Sensors by basilfx, PlantWatering PCB02 by Benedikt3141, Rf room sensor hw by dselcan and ESP DEV BOARD by hamayanShowa-ele.
The CCS811 in open source designs
The gallery holds 7 open source boards using the CCS811 from 6 GitHub repositories; a typical one measures about 92.5 × 55.5 mm and carries around 41 components.
83% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Environmental-Sensors by basilfx.
Microcontrollers on boards using the CCS811
What boards using the CCS811 are built for
CCS811: common questions
Where can I find a CCS811 reference design?
Each of the 7 boards on this page is a real design using the CCS811. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the CCS811 RESET pin?
The RESET pin has a pull-up to 3.3V on 5 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the CCS811.
What pull-up resistor is used on the CCS811 SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the CCS811.
What pull-up resistor is used on the CCS811 SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 4 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the CCS811.
Which microcontrollers do boards using the CCS811 use?
Most are built on AVR/Arduino (2) and ESP32 (2).
How big is a typical board using the CCS811?
The median is 92.5 × 55.5 mm, and 83% are two-layer designs.
What is the most popular open source board using the CCS811?
By GitHub stars, Environmental-Sensors by basilfx, with 24 stars.
Can I simulate one of these boards using the CCS811 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.