9 open source boards using the CD4053B
Real designs built with the CD4053B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Core
shmoergh
215 × 100 mm285 parts2LNo license124INK4u Board
TheEccentricGenius
68.6 × 53.3 mm59 parts2LCERN-OHL-W-2.05TM LPG-MIX
clarionut
89.5 × 98.4 mm56 parts2LNo license5RP2040/RP2350
Digirig icom
1vers1on
48.5 × 56 mm60 parts4LNo license1ESP32
PLL AM OSC 1 7
Gloeidraad
160 × 100 mm168 parts2LNo license0ProjectSoloJam
JosephFiddes
245 × 180 mm96 parts4LNo license0- schematic only · 36 partsAVR/Arduino
Breadboard-Power-Supply
leboeuf-dup
36 parts2LNo license0 ESP32
PLL AM OSC 1 5a
Gloeidraad
159.5 × 99.5 mm161 parts2LNo license03-phase lfo
tpcarlson
30 × 128.5 mm70 parts2LNo license106
How designs wire the CD4053B
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the CD4053B connects to, and the resistors, capacitors and other passives placed on it.
- The B1 pin has a series resistor on 6 of 7 designs, most often 470 Ω (then 22 kΩ).
- The INH pin is tied to GND on 6 of 7 designs.
- The VEE pin is tied to GND on 6 of 7 designs.
- The VDD pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| B1pin 1 | Connected to: Signal 100% |
|
| B0pin 2 | Connected to: A connector 57% |
|
| C1pin 3 | Connected to: A connector 29% |
|
| C0pin 5 | Connected to: A connector 71% |
|
| INHpin 6 | Connected to: GND 86% | — |
| VEEpin 7 | Connected to: GND 86% | — |
| VSSpin 8 | Connected to: GND 86% | — |
| A0pin 12 | Connected to: A connector 57% · not connected 29% |
|
| VDDpin 16 | Connected to: 12V 86% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Core by shmoergh, 3-phase lfo by tpcarlson, TM LPG-MIX by clarionut and INK4u Board by TheEccentricGenius.
The CD4053B in open source designs
The gallery holds 9 open source boards using the CD4053B from 8 GitHub repositories; a typical one measures about 124.5 × 99.8 mm and carries around 70 components.
78% are two-layer designs, the rest use four layers or more, and 11% carry an open source license.
The most starred is Core by shmoergh.
Microcontrollers on boards using the CD4053B
What boards using the CD4053B are built for
CD4053B: common questions
Where can I find a CD4053B reference design?
Each of the 9 boards on this page is a real design using the CD4053B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the CD4053B B1 pin?
The B1 pin has a series resistor on 6 of 7 designs, most often 470 Ω (then 22 kΩ). Counted from the KiCad layouts of 7 open source designs using the CD4053B.
How is the CD4053B INH pin connected?
The INH pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the CD4053B.
How is the CD4053B VEE pin connected?
The VEE pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the CD4053B.
What parts are used alongside the CD4053B?
The TL072, LM311, LM358 and TL074 appear in the most repositories here.
Which microcontrollers do boards using the CD4053B use?
Most are built on ESP32 (2), AVR/Arduino (1) and RP2040/RP2350 (1).
How big is a typical board using the CD4053B?
The median is 124.5 × 99.8 mm, and 78% are two-layer designs.
What is the most popular open source board using the CD4053B?
By GitHub stars, Core by shmoergh, with 124 stars.
Can I simulate one of these boards using the CD4053B before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.