14 open source boards using the DRV8835
Real designs built with the DRV8835, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Makennbot
idlehandsdev
60 × 75 mm53 parts2LNo license175ESP8266
Espway
espway
43 × 34.3 mm33 parts2LLGPL-3.0122NXP
McuOpenPnP Machine
ErichStyger
3.5 × 2.5 mm55 parts2LNo license69STM32
MIZUHO
idt12312
75.1 × 85.2 mm106 parts2LNo license28STM32
Vert Board rev3
tokoro10g
36 × 52.5 mm115 parts4LCustom license7Microchip SAM
ElectronutLabs-ZeroDriver
electronut
60 × 22.9 mm41 parts2LNo license5STM32
Mercury v2.1
Teruru-52
72.8 × 100 mm154 parts2LNo license1STM32
Ratibroombroom
aindustriosa
66 × 60 mm114 parts2LNo license1STM32
PCB ApiaryWaterDispensingSystem
Mateuszworo97
217.3 × 127.3 mm182 parts2LNo license0ESP32
Cat gpt
yudai0804
70 × 70 mm20 parts2LNo license0- schematic only · 98 partsSTM32
Shu poyo
shu-13
98 partsMIT0 - schematic only · 94 partsSTM32
Rattack v2
mij001
94 partsNo license0 STM32
Mercury v2
Teruru-52
72.8 × 100 mm147 parts2LNo license1STM32
Quatro
Teruru-52
100 × 72.8 mm98 parts2LNo license1
How designs wire the DRV8835
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the DRV8835 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF (then 2.2 µF).
- The VM pin has a capacitor to GND on 8 of 10 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VMpin 1 | Connected to: BATT 50% · a signal 50% |
|
| GNDpin 6 | Connected to: GND 100% | — |
| MODEpin 11 | Connected to: The microcontroller 30% · GND 30% · 3.3V 30% |
|
| VCCpin 12 | Connected to: 3.3V 90% |
|
| GND_TPpin 13 | Connected to: GND 80% · not connected 20% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Makennbot by idlehandsdev, Espway by espway, McuOpenPnP Machine by ErichStyger and MIZUHO by idt12312.
The DRV8835 in open source designs
The gallery holds 14 open source boards using the DRV8835 from 12 GitHub repositories; a typical one measures about 68 × 71.4 mm and carries around 98 components.
92% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is Makennbot by idlehandsdev.
Parts used alongside the DRV8835
Microcontrollers on boards using the DRV8835
What boards using the DRV8835 are built for
DRV8835: common questions
Where can I find a DRV8835 reference design?
Each of the 14 boards on this page is a real design using the DRV8835. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the DRV8835 VCC pin?
The VCC pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 10 open source designs using the DRV8835.
How is the DRV8835 VM pin connected?
The VM pin has a capacitor to GND on 8 of 10 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 10 open source designs using the DRV8835.
What parts are used alongside the DRV8835?
The STM32F405RGTx, 74AHC1G125 and AD8604 appear in the most repositories here.
Which microcontrollers do boards using the DRV8835 use?
Most are built on STM32 (9), Microchip SAM (2), ESP32 (1) and ESP8266 (1).
How big is a typical board using the DRV8835?
The median is 68 × 71.4 mm, and 92% are two-layer designs.
What is the most popular open source board using the DRV8835?
By GitHub stars, Makennbot by idlehandsdev, with 175 stars.
Can I simulate one of these boards using the DRV8835 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.