23 open source boards using the 74AHC1G125
Real designs built with the 74AHC1G125, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Makennbot
idlehandsdev
60 × 75 mm53 parts2LNo license175Microchip SAM
POV Fidget
idlehandsdev
71.9 × 65.7 mm66 parts2LNo license54Microchip SAM
ATmega SAT
spel-uchile
96 × 89.9 mm65 parts2LNo license6Microchip SAM
ElectronutLabs-ZeroDriver
electronut
60 × 22.9 mm41 parts2LNo license5RP2040/RP2350
Chastity
brad-za
138.3 × 111 mm336 parts2LNo license4ESP32
Genesis Board
iffycodes
165.8 × 119.2 mm89 parts2LNo license2Usbhid daq
shraken
63.9 × 37.1 mm69 parts4LNo license2Particle bamf23-badge
particle-iot
54 × 86 mm50 parts2LCC-BY-SA-4.02Washington metro
funvill
202.9 × 172.7 mm325 parts2LNo license1Power
foxsi
119.4 × 62.5 mm204 parts4LNo license1STM32
PCB DRONE C8
ArduProject
102 × 49 mm140 parts4LMIT1AVR/Arduino
Z80Card
galjonsfigur
85.6 × 54 mm77 parts2LGPL-3.01Microchip SAM
Control
versioduo
60 × 35 mm48 parts4LNo license1Microchip SAM
Wave
versioduo
60 × 60 mm101 parts4LNo license0Microchip SAM
EE156 4 Layer
valex2
99 × 41.5 mm82 parts4LNo license0Microchip SAM
FanFDD
idlehandsdev
88 × 88 mm57 parts2LNo license0AVR/Arduino
Piano Lights
ddribin
98 × 51.6 mm36 parts2LMIT0Rhythmsquid
edwindertien
39.3 × 21.2 mm13 parts2LNo license0ESP32
Output.v25Panel
maholli
100 × 100 mm45 partsNo license42RP2040/RP2350
ChastityRightV2
brad-za
137.3 × 111 mm286 parts2LNo license4Microchip SAM
KairosV2
valex2
99 × 41.5 mm82 parts4LNo license0ESP32
V25Panel
maholli
100 × 100 mm45 partsNo license42Adafruit Ethernet FeatherWing
iffycodes
55.9 × 22.9 mm47 parts2LNo license2
How designs wire the 74AHC1G125
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the 74AHC1G125 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 9 of 19 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OEpin 1 | Connected to: A connector 42% · GND 32% |
|
| GNDpin 3 | Connected to: GND 89% | — |
| VCCpin 5 | Connected to: 3.3V 84% · a signal 16% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Makennbot by idlehandsdev, POV Fidget by idlehandsdev, Output.v25Panel by maholli and ATmega SAT by spel-uchile.
The 74AHC1G125 in open source designs
The gallery holds 23 open source boards using the 74AHC1G125 from 19 GitHub repositories; a typical one measures about 96 × 62.5 mm and carries around 66 components.
67% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Makennbot by idlehandsdev.
Parts used alongside the 74AHC1G125
Microcontrollers on boards using the 74AHC1G125
What boards using the 74AHC1G125 are built for
74AHC1G125: common questions
Where can I find a 74AHC1G125 reference design?
Each of the 23 boards on this page is a real design using the 74AHC1G125. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 74AHC1G125 VCC pin?
The VCC pin has a decoupling capacitor on 9 of 19 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 19 open source designs using the 74AHC1G125.
What parts are used alongside the 74AHC1G125?
The AP2112K-3.3V, SAMD21G18, DRV8835, MCP73831T and TPS78433QWDRBRQ1 appear in the most repositories here.
Which microcontrollers do boards using the 74AHC1G125 use?
Most are built on Microchip SAM (9), ESP32 (3), AVR/Arduino (2) and RP2040/RP2350 (2).
How big is a typical board using the 74AHC1G125?
The median is 96 × 62.5 mm, and 67% are two-layer designs.
What is the most popular open source board using the 74AHC1G125?
By GitHub stars, Makennbot by idlehandsdev, with 175 stars.
Can I simulate one of these boards using the 74AHC1G125 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.