7 open source boards using the ESP-01S

Real designs built with the ESP-01S, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the ESP-01S

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ESP-01S connects to, and the resistors, capacitors and other passives placed on it.

  • The GPIO_0 pin is left unconnected on 4 of 5 designs.
  • The CH_PD pin is left unconnected on 3 of 5 designs (a signal on 2).
  • The GPIO_2 pin is left unconnected on 3 of 5 designs.
  • The RST pin is left unconnected on 3 of 5 designs.
GNDpin 2Connected to: GND 60% · not connected 20% · a signal 20%
CH_PDpin 3Connected to: Not connected 60% · a signal 40%
GPIO_2pin 4Connected to: Not connected 60% · 3.3V 20% · a signal 20%
RSTpin 5Connected to: Not connected 60% · 3.3V 20% · a signal 20%
GPIO_0pin 6Connected to: Not connected 80% · a signal 20%
VCCpin 7Connected to: 3.3V 60% · not connected 40%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bed occupancy by thorio, LineFollower-Speedy- by Club-robotica-UDLSB, Dispensador Garrafones V2.0 by EmersonEE and Solder-Fume-Extractor by James-Lian.

The ESP-01S in open source designs

The gallery holds 7 open source boards using the ESP-01S from 6 GitHub repositories; a typical one measures about 74.9 × 85.1 mm and carries around 29 components.

100% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.

The most starred is Doorbell sensor by thorio.

Microcontrollers on boards using the ESP-01S

ESP-01S: common questions

Where can I find a ESP-01S reference design?

Each of the 7 boards on this page is a real design using the ESP-01S. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ESP-01S GPIO_0 pin connected?

The GPIO_0 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ESP-01S.

How is the ESP-01S CH_PD pin connected?

The CH_PD pin is left unconnected on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the ESP-01S.

How is the ESP-01S GPIO_2 pin connected?

The GPIO_2 pin is left unconnected on 3 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ESP-01S.

What parts are used alongside the ESP-01S?

The AMS1117-3.3, AMS1117-5.0, CD74HC4067SM, DRV8825_breakout and LM1117MP-ADJ appear in the most repositories here.

Which microcontrollers do boards using the ESP-01S use?

Most are built on ESP8266 (4), AVR/Arduino (1) and STM32 (1).

How big is a typical board using the ESP-01S?

The median is 74.9 × 85.1 mm, and 100% are two-layer designs.

What is the most popular open source board using the ESP-01S?

By GitHub stars, Doorbell sensor by thorio, with 28 stars.

Can I simulate one of these boards using the ESP-01S before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part