9 open source boards using the ESP-PSRAM32

Real designs built with the ESP-PSRAM32, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the ESP-PSRAM32

Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ESP-PSRAM32 connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 8 of 8 designs, most often 100 nF (then 10 µF).
  • The CE pin has a pull-up to 3.3V on 5 of 8 designs, most often 10 kΩ.
CEpin 1Connected to: The microcontroller 38%, a connector 25%
  • Pull-up to 3.3V on 63% · 10 kΩ (5)
VSSpin 4Connected to: GND 100%
VCCpin 8Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (12), 10 µF (1), 22 µF (1)

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pico stretch by jvanderberg, Dip64 gw by andrastantos, 16EJU24 by AlexEkb4ever and Frank air by rh1tech.

The ESP-PSRAM32 in open source designs

The gallery holds 9 open source boards using the ESP-PSRAM32 from 8 GitHub repositories; a typical one measures about 57.2 × 24.6 mm and carries around 59 components.

56% use four copper layers or more, and 22% carry an open source license.

The most starred is Pico stretch by jvanderberg.

Microcontrollers on boards using the ESP-PSRAM32

What boards using the ESP-PSRAM32 are built for

ESP-PSRAM32: common questions

Where can I find a ESP-PSRAM32 reference design?

Each of the 9 boards on this page is a real design using the ESP-PSRAM32. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ESP-PSRAM32 VCC pin?

The VCC pin has a decoupling capacitor on 8 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the ESP-PSRAM32.

What pull-up resistor is used on the ESP-PSRAM32 CE pin?

The CE pin has a pull-up to 3.3V on 5 of 8 designs, most often 10 kΩ. Counted from the KiCad layouts of 8 open source designs using the ESP-PSRAM32.

What parts are used alongside the ESP-PSRAM32?

The C42415655, C427602, C97521, CH340C and MW7211A appear in the most repositories here.

Which microcontrollers do boards using the ESP-PSRAM32 use?

Most are built on RP2040/RP2350 (6) and FPGA (1).

How big is a typical board using the ESP-PSRAM32?

The median is 57.2 × 24.6 mm, and 44% are two-layer designs.

What is the most popular open source board using the ESP-PSRAM32?

By GitHub stars, Pico stretch by jvanderberg, with 24 stars.

Can I simulate one of these boards using the ESP-PSRAM32 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part