10 open source boards using the ESP32-WROVER-E-N16R8
Real designs built with the ESP32-WROVER-E-N16R8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ControlBoard
paradise-fi
76 × 76 mm207 parts4LCC-BY-NC-4.042ESP32
A Computer
alexlutsenko7
84.1 × 83.4 mm87 parts4LMIT2ESP32
Speaker pod
MostlyBuilds
86.2 × 50.2 mm93 parts2LCC-BY-SA-4.01ESP32
SparkFun RTK Facet mosaic
sparkfun
59.5 × 43 mm129 parts4LMIT0ESP32
Tangara mainboard
dpaola2
52 × 94.2 mm95 parts4LNo license0ESP32
Dc33 floridaman
badgelife
85.5 × 85.7 mm76 parts2LNo license0ESP32
Daronjli dongle
manhoosbilli1
45.2 × 29.7 mm50 parts4LNo license0ESP32
Arcade
RishitJain-dev
95.5 × 72.5 mm48 parts2LNo license0ESP32
Jpod
Jake-Eshelman-Portfolio
56.5 × 70.5 mm10 parts2LNo license0ESP32
SparkFun RTK Facet mosaic panelized
sparkfun
133.2 × 187.2 mm129 parts4LMIT0
How designs wire the ESP32-WROVER-E-N16R8
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the ESP32-WROVER-E-N16R8 connects to, and the resistors, capacitors and other passives placed on it.
- The 3V3 pin is tied to 3.3V on 9 of 10 designs.
- The EN pin has a capacitor to GND on 7 of 10 designs, most often 1 µF (then 100 nF).
- The EN pin has a pull-up to 3.3V on 5 of 10 designs, most often 10 kΩ (then 12 kΩ).
- The SENSOR_VN/GPIO39/ADC1_CH pin is left unconnected on 6 of 10 designs (a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 15, 38, 39 | Connected to: GND 79% | — |
| 3V3pin 2 | Connected to: 3.3V 90% | — |
| ENpin 3 | Connected to: A connector 20%, the microcontroller 20% |
|
| SENSOR_VN/GPIO39/ADC1_CHpin 5 | Connected to: Not connected 60% · a signal 40% | — |
| GPIO34/ADC1_CH6pin 6 | Connected to: Signal 60% · not connected 40% |
|
| GPIO35/ADC1_CH7pin 7 | Connected to: The microcontroller 20%, a connector 20% · not connected 20% |
|
| NCpin 17, 18, 19, 20, 21, 22, 27, 28, 32 | Connected to: Not connected 100% | — |
| IO0pin 25 | Connected to: The microcontroller 20% · not connected 20% |
|
| IO5pin 29 | Connected to: Not connected 60% · a signal 40% | — |
19 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ControlBoard by paradise-fi, A Computer by alexlutsenko7, Upet wifi by fachat and Speaker pod pcb by MostlyBuilds.
The ESP32-WROVER-E-N16R8 in open source designs
The gallery holds 10 open source boards using the ESP32-WROVER-E-N16R8 from 9 GitHub repositories; a typical one measures about 80.1 × 74.3 mm and carries around 90 components.
60% use four copper layers or more, and 40% carry an open source license.
The most starred is ControlBoard by paradise-fi.
Parts used alongside the ESP32-WROVER-E-N16R8
Microcontrollers on boards using the ESP32-WROVER-E-N16R8
What boards using the ESP32-WROVER-E-N16R8 are built for
ESP32-WROVER-E-N16R8: common questions
Where can I find a ESP32-WROVER-E-N16R8 reference design?
Each of the 10 boards on this page is a real design using the ESP32-WROVER-E-N16R8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP32-WROVER-E-N16R8 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 9 of 10 designs. Counted from the KiCad layouts of 10 open source designs using the ESP32-WROVER-E-N16R8.
How is the ESP32-WROVER-E-N16R8 EN pin connected?
The EN pin has a capacitor to GND on 7 of 10 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 10 open source designs using the ESP32-WROVER-E-N16R8.
How is the ESP32-WROVER-E-N16R8 SENSOR_VN/GPIO39/ADC1_CH pin connected?
The SENSOR_VN/GPIO39/ADC1_CH pin is left unconnected on 6 of 10 designs (a signal on 4). Counted from the KiCad layouts of 10 open source designs using the ESP32-WROVER-E-N16R8.
Which microcontrollers do boards using the ESP32-WROVER-E-N16R8 use?
Most are built on ESP32 (10).
How big is a typical board using the ESP32-WROVER-E-N16R8?
The median is 80.1 × 74.3 mm, and 40% are two-layer designs.
What is the most popular open source board using the ESP32-WROVER-E-N16R8?
By GitHub stars, ControlBoard by paradise-fi, with 42 stars.
Can I simulate one of these boards using the ESP32-WROVER-E-N16R8 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.