21 open source boards using the INA181
Real designs built with the INA181, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Td deflect
tdaede
174 × 104 mm165 parts4LNo license370STM32
MESC FOC ESC
davidmolony
84 × 66.5 mm183 parts4LBSD-3-Clause60Downscaled Inverters
Bausager
139.7 × 116.8 mm111 parts2LNo license7STM32
BLDC
banbatakumi
40 × 40 mm87 parts2LNo license1STM32
Bread board
cr1tbit
100 × 77 mm224 parts4LNo license0Mosfets
abd-alaj
222.5 × 104.5 mm121 parts4LNo license0AVR/Arduino
Pdb
0x007E
77.5 × 50.8 mm110 parts2LCC-BY-NC-4.00DIY-amplifier
adamkral20-svg
90.9 × 71.6 mm91 parts4LNo license0RISC-V
Bidirectional tester
c3am
68 × 60 mm70 parts2LNo license0STM32
Sarwan1494.github.io
Sarwan1494
42 × 42 mm67 parts4LNo license0AVR/Arduino
Power
simle-stardust
115 × 75 mm51 parts2LMIT0AVR/Arduino
Two motor
owhite
78 × 60 mm43 parts4LNo license0KAPTON-CONNECTOR
AslanLauzon
90 × 76 mm28 parts2LNo license0AVR/Arduino
ControlBoard rev05a
plertvilai
44.5 × 57.8 mm64 parts2LMIT7STM32
Stm8-car
akrapivniy
60 × 60 mm42 parts2LGPL-3.06Powerstrip left
Jiggolino
37 × 100 mm37 parts4LCustom license1ESP32
Hubby
cr1tbit
100 × 77 mm212 parts4LNo license0AVR/Arduino
Unrouted
plertvilai
44.5 × 57.8 mm63 parts2LMIT7Powerstrip right
Jiggolino
37 × 100 mm37 parts4LCustom license1PWM 6 step SVPWM IR2110
abd-alaj
77.7 × 84.3 mm42 parts2LNo license0AVR/Arduino
TRANSMITTER SMD
vul-os
39.4 × 54.3 mm12 parts2LMIT0
How designs wire the INA181
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the INA181 connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 13 of 17 designs, most often 100 nF (then 1 µF).
- The + pin has a series resistor on 9 of 17 designs, most often 10 kΩ (then 100 mΩ).
- The + pin has a resistor to GND on 7 of 17 designs, most often 10 mΩ (then 100 mΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 41% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| +pin 3 | Connected to: Signal 88% |
|
| V+pin 6 | Connected to: 3.3V 94% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Td deflect by tdaede, MESC FOC ESC by davidmolony, Downscaled Inverters by Bausager and ControlBoard rev05a by plertvilai.
The INA181 in open source designs
The gallery holds 21 open source boards using the INA181 from 17 GitHub repositories; a typical one measures about 77.7 × 71.6 mm and carries around 67 components.
52% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Td deflect by tdaede.
Parts used alongside the INA181
Microcontrollers on boards using the INA181
What boards using the INA181 are built for
INA181: common questions
Where can I find a INA181 reference design?
Each of the 21 boards on this page is a real design using the INA181. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the INA181 V+ pin?
The V+ pin has a decoupling capacitor on 13 of 17 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 17 open source designs using the INA181.
What resistor goes on the INA181 + pin?
The + pin has a series resistor on 9 of 17 designs, most often 10 kΩ (then 100 mΩ). Counted from the KiCad layouts of 17 open source designs using the INA181.
Which microcontrollers do boards using the INA181 use?
Most are built on AVR/Arduino (6), STM32 (6), ESP32 (1) and RISC-V (1).
How big is a typical board using the INA181?
The median is 77.7 × 71.6 mm, and 52% are two-layer designs.
What is the most popular open source board using the INA181?
By GitHub stars, Td deflect by tdaede, with 370 stars.
Can I simulate one of these boards using the INA181 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.