11 open source boards using the INA219BxDCN
Real designs built with the INA219BxDCN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PIC
VFD Clock
drewsum
200 × 50 mm458 parts2LNo license1PIC
Nixie Clock
drewsum
200 × 50 mm322 parts4LNo license0Breakoutpcbs
dodotronix
43.9 × 47.5 mm108 parts2LNo license0ESP32
StartrackerOrion-Hardware
NBER08
86.1 × 71.9 mm96 parts4LMIT0MINTS DREAM V2
Dheerajsom
79 × 78.9 mm33 parts2LMIT0- schematic only · 58 parts
EEE3088Proj
SanjanNaidoo
58 partsNo license0 ESP32
VolPak-1000
raybello
153.7 × 108.5 mm185 parts4LNo license0ESP32
LoRa tracker
bendelathouwer
116.3 × 114.5 mm53 parts2LNo license0Som asset tracker
bendelathouwer
100 × 100 mm44 parts2LNo license0Som asset tracker small
bendelathouwer
39.5 × 53.6 mm38 parts2LNo license0PowerModule
tokai-student-rocket-project
90 × 70 mm41 parts2LNo license0
How designs wire the INA219BxDCN
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the INA219BxDCN connects to, and the resistors, capacitors and other passives placed on it.
- The VS pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF).
- The IN+ pin has a series resistor on 6 of 8 designs, most often 10 Ω (then 100 Ω).
- The SDA pin has a pull-up to 3.3V on 6 of 8 designs, most often 10 kΩ (then 47 kΩ).
- The A0 pin is tied to GND on 7 of 8 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN+pin 1 | Connected to: Signal 75% · BATT 25% |
|
| IN-pin 2 | Connected to: Signal 88% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| VSpin 4 | Connected to: 3.3V 100% |
|
| SCLpin 5 | Connected to: A connector 50%, the microcontroller 38%, DS1683 25% |
|
| SDApin 6 | Connected to: A connector 50%, the microcontroller 38%, DS1683 25% |
|
| A0pin 7 | Connected to: GND 88% | — |
| A1pin 8 | Connected to: GND 88% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include VFD Clock by drewsum, LoRa tracker by bendelathouwer, MINTS DREAM V2 by Dheerajsom and Breakoutpcbs by dodotronix.
The INA219BxDCN in open source designs
The gallery holds 11 open source boards using the INA219BxDCN from 9 GitHub repositories; a typical one measures about 95 × 71 mm and carries around 58 components.
70% are two-layer designs, the rest use four layers or more, and 18% carry an open source license.
The most starred is VFD Clock by drewsum.
Parts used alongside the INA219BxDCN
What boards using the INA219BxDCN are built for
INA219BxDCN: common questions
Where can I find a INA219BxDCN reference design?
Each of the 11 boards on this page is a real design using the INA219BxDCN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the INA219BxDCN VS pin?
The VS pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the INA219BxDCN.
What resistor goes on the INA219BxDCN IN+ pin?
The IN+ pin has a series resistor on 6 of 8 designs, most often 10 Ω (then 100 Ω). Counted from the KiCad layouts of 8 open source designs using the INA219BxDCN.
What pull-up resistor is used on the INA219BxDCN SDA pin?
The SDA pin has a pull-up to 3.3V on 6 of 8 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 8 open source designs using the INA219BxDCN.
What parts are used alongside the INA219BxDCN?
The 74LVC1G97, 74VHC541, DS1683, DS3231MZ and FT234XD appear in the most repositories here.
Which microcontrollers do boards using the INA219BxDCN use?
Most are built on ESP32 (3) and PIC (2).
How big is a typical board using the INA219BxDCN?
The median is 95 × 71 mm, and 70% are two-layer designs.
What is the most popular open source board using the INA219BxDCN?
By GitHub stars, VFD Clock by drewsum, with 1 stars.
Can I simulate one of these boards using the INA219BxDCN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.