8 open source boards using the ISO1050
Real designs built with the ISO1050, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
ChibiESC
joewa
143.5 × 14 mm187 parts4LGPL-3.010STM32
VESC-controller
paltatech
160 × 90 mm336 parts4LNo license356PIC
All in One Railroad Interface
GBert
85 × 56.5 mm151 parts2LNo license99Opel velocity interface
MITEVT
132.1 × 57.2 mm39 parts2LMIT1Devboard panelized
MITEVT
201.9 × 148.6 mm35 parts2LNo license0PIC
BPi-CAN
GBert
100 × 100 mm146 parts2LNo license99Opel velocity interfaec
MITEVT
56.3 × 34.3 mm35 parts2LMIT1RPi-MCP2515
GBert
65 × 56.5 mm42 parts2LNo license99
How designs wire the ISO1050
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ISO1050 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 7 has a series resistor on 5 of 5 designs, most often 120 Ω (then 60.4 Ω).
- Pin 1 is tied to 3.3V on 5 of 5 designs.
- Pin 4 is tied to GND on 5 of 5 designs.
- Pin 1 has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 2.2 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: 3.3V 100% |
|
| Pin 4 | Connected to: GND 100% | — |
| Pin 5 | Connected to: GND 80% · a signal 20% | — |
| Pin 6 | Connected to: A connector 100% |
|
| Pin 7 | Connected to: A connector 100% |
|
| Pin 8 | Connected to: 5V 60% · a signal 40% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include VESC-controller by paltatech, All in One Railroad Interface by GBert, ChibiESC by joewa and Opel velocity interface by MITEVT.
The ISO1050 in open source designs
The gallery holds 8 open source boards using the ISO1050 from 5 GitHub repositories; a typical one measures about 116 × 56.8 mm and carries around 94 components.
75% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is VESC-controller by paltatech.
Parts used alongside the ISO1050
What boards using the ISO1050 are built for
ISO1050: common questions
Where can I find a ISO1050 reference design?
Each of the 8 boards on this page is a real design using the ISO1050. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the ISO1050 pin 7?
Pin 7 has a series resistor on 5 of 5 designs, most often 120 Ω (then 60.4 Ω). Counted from the KiCad layouts of 5 open source designs using the ISO1050.
How is the ISO1050 pin 1 connected?
Pin 1 is tied to 3.3V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ISO1050.
How is the ISO1050 pin 4 connected?
Pin 4 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ISO1050.
What parts are used alongside the ISO1050?
The LPC11C14, MCP1755 and MCP2515_TSSOP appear in the most repositories here.
Which microcontrollers do boards using the ISO1050 use?
Most are built on PIC (2) and STM32 (2).
How big is a typical board using the ISO1050?
The median is 116 × 56.8 mm, and 75% are two-layer designs.
What is the most popular open source board using the ISO1050?
By GitHub stars, VESC-controller by paltatech, with 356 stars.
Can I simulate one of these boards using the ISO1050 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.