12 open source boards using the LM317_TO-252

Real designs built with the LM317_TO-252, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

12 boardsClear filters|Most starred

How designs wire the LM317_TO-252

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LM317_TO-252 connects to, and the resistors, capacitors and other passives placed on it.

  • The VI pin has a capacitor to GND on 8 of 9 designs, most often 100 nF (then 10 µF).
  • The ADJ pin has a series resistor on 5 of 9 designs, most often 1 kΩ (then 330 Ω).
  • The VO pin has a series resistor on 5 of 9 designs, most often 330 Ω (then 240 Ω).
  • The VO pin has a capacitor to GND on 4 of 9 designs, most often 22 µF (then 100 nF).
ADJpin 1Connected to: A connector 22% · 2.5V 22%
  • Series resistor on 56% · 1 kΩ (2), 330 Ω (2), 500 Ω (1)
  • Capacitor to GND on 33% · 2.2 µF (1), 10 µF (1)
VOpin 2Connected to: A connector 22%, OPA189 22% · 2.5V 44%
  • Series resistor on 56% · 330 Ω (2), 240 Ω (1), 10 Ω (1)
  • Capacitor to GND on 44% · 22 µF (2), 100 nF (2), 1 µF (1)
VIpin 3Connected to: Signal 56% · 3.3V 44%
  • Capacitor to GND on 89% · 100 nF (3), 10 µF (3), 47 µF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ep2c35 trial by tomverbeure, LM317regulador by Pacheco55, SimpleDigital by codeandrelax and PI wt hold for laser intensity lock by JQIamo.

The LM317_TO-252 in open source designs

The gallery holds 12 open source boards using the LM317_TO-252 from 9 GitHub repositories; a typical one measures about 76.2 × 67.8 mm and carries around 122 components.

50% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.

The most starred is Ep2c35 trial by tomverbeure.

Parts used alongside the LM317_TO-252

Microcontrollers on boards using the LM317_TO-252

What boards using the LM317_TO-252 are built for

LM317_TO-252: common questions

Where can I find a LM317_TO-252 reference design?

Each of the 12 boards on this page is a real design using the LM317_TO-252. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LM317_TO-252 VI pin connected?

The VI pin has a capacitor to GND on 8 of 9 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 9 open source designs using the LM317_TO-252.

What resistor goes on the LM317_TO-252 ADJ pin?

The ADJ pin has a series resistor on 5 of 9 designs, most often 1 kΩ (then 330 Ω). Counted from the KiCad layouts of 9 open source designs using the LM317_TO-252.

What resistor goes on the LM317_TO-252 VO pin?

The VO pin has a series resistor on 5 of 9 designs, most often 330 Ω (then 240 Ω). Counted from the KiCad layouts of 9 open source designs using the LM317_TO-252.

What parts are used alongside the LM317_TO-252?

The BUF634A, INA849, LM337_TO252, LM4040DBZ-5 and OPA189 appear in the most repositories here.

Which microcontrollers do boards using the LM317_TO-252 use?

Most are built on AVR/Arduino (2) and PIC (2).

How big is a typical board using the LM317_TO-252?

The median is 76.2 × 67.8 mm, and 50% are two-layer designs.

What is the most popular open source board using the LM317_TO-252?

By GitHub stars, Ep2c35 trial by tomverbeure, with 5 stars.

Can I simulate one of these boards using the LM317_TO-252 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part