10 open source boards using the LM317L_TO92
Real designs built with the LM317L_TO92, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Edromufu
edromufu
57.5 × 38.5 mm26 parts2LMIT9PIC
FuelGauge
davefiddes
94 × 44 mm27 parts2LGPL-3.05EPROM Prog PS
AebrahmRamos
26.7 × 42.9 mm25 parts2LNo license1Lab psu
jfjhh
76.2 × 76.2 mm63 parts2LNo license0Spectrum Analyzer: IF and Log Amp
dmsmccann
91.7 × 48.8 mm62 parts2LNo license0Pssst TX final amp
mostlydiyrf
101.6 × 30.6 mm37 parts2LCC-BY-NC-4.06Spectrum Analyzer: IF and Log Amp
dmsmccann
91.7 × 48.8 mm55 parts2LNo license0Io card
nojan1
230 × 100 mm61 parts2LNo license0Parte2
MyCloudExample
50 × 50 mm9 parts2LNo license1- schematic only · 431 parts
W7ZOI Spectrum Analyzer
dmsmccann
431 parts2LNo license0
How designs wire the LM317L_TO92
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LM317L_TO92 connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ pin has a series resistor on 6 of 8 designs, most often 220 Ω (then 270 Ω).
- The VO pin has a series resistor on 6 of 8 designs, most often 220 Ω (then 270 Ω).
- The VI pin has a capacitor to GND on 5 of 8 designs, most often 100 nF (then 4.7 mF).
- The VO pin has a capacitor to GND on 4 of 8 designs, most often 100 nF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: Signal 88% |
|
| VOpin 2 | Connected to: Signal 75% · 10 25% |
|
| VIpin 3 | Connected to: A connector 25% · 5V 38% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Edromufu by edromufu, Pssst TX final amp by mostlydiyrf, FuelGauge by davefiddes and EPROM Prog PS by AebrahmRamos.
The LM317L_TO92 in open source designs
The gallery holds 10 open source boards using the LM317L_TO92 from 8 GitHub repositories; a typical one measures about 91.7 × 48.8 mm and carries around 46 components.
100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Edromufu by edromufu.
Microcontrollers on boards using the LM317L_TO92
What boards using the LM317L_TO92 are built for
LM317L_TO92: common questions
Where can I find a LM317L_TO92 reference design?
Each of the 10 boards on this page is a real design using the LM317L_TO92. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM317L_TO92 ADJ pin?
The ADJ pin has a series resistor on 6 of 8 designs, most often 220 Ω (then 270 Ω). Counted from the KiCad layouts of 8 open source designs using the LM317L_TO92.
What resistor goes on the LM317L_TO92 VO pin?
The VO pin has a series resistor on 6 of 8 designs, most often 220 Ω (then 270 Ω). Counted from the KiCad layouts of 8 open source designs using the LM317L_TO92.
How is the LM317L_TO92 VI pin connected?
The VI pin has a capacitor to GND on 5 of 8 designs, most often 100 nF (then 4.7 mF). Counted from the KiCad layouts of 8 open source designs using the LM317L_TO92.
Which microcontrollers do boards using the LM317L_TO92 use?
Most are built on PIC (1).
How big is a typical board using the LM317L_TO92?
The median is 91.7 × 48.8 mm, and 100% are two-layer designs.
What is the most popular open source board using the LM317L_TO92?
By GitHub stars, Edromufu by edromufu, with 9 stars.
Can I simulate one of these boards using the LM317L_TO92 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.