19 open source boards using the LM393DR
Real designs built with the LM393DR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
HolyGrail
whbCool
157 × 73 mm195 parts6LNo license1STM32
Flyback-Driver
Operationorange01
128 × 72.5 mm115 parts4LNo license1RP2040/RP2350
Digirig icom
1vers1on
48.5 × 56 mm60 parts4LNo license1Nova pcb v6 power v2
Ace2932
112 × 90 mm57 parts4LMIT1ESP32
Compact-S1-placement
ddasdkimo
160 × 110 mm694 parts2LNo license0ESP32
Ee115-capstone
tsaimatthew
115.8 × 98.6 mm187 parts2LNo license0Eload-60v
metallarox
170 × 125 mm132 parts2LCERN-OHL-S-2.00ESP32
Vaporizer
itspolly
73.8 × 73.9 mm108 parts2LUnlicense0ESP32
OpenRower
naibaf7
55 × 45 mm65 parts2LMIT0Spectre
mkrmx
42 × 32 mm38 parts2LMIT0ESP32
Layout-S2-review
ddasdkimo
200 × 170 mm694 parts2LNo license0MuKOB / RPi / USB - Key/Paddle&Sounder Interface MkIV
MorseKOB
104.1 × 78.7 mm75 parts2LMIT0BSPD
MADHURAMAN-afk
82.5 × 71.5 mm63 parts2LNo license0Spectre tht
mkrmx
46 × 40 mm38 parts2LMIT0ESP32
Routing-R0
ddasdkimo
200 × 170 mm694 parts2LNo license0MuKOB / RPi / USB - Key/Paddle&Sounder Interface MkIII
MorseKOB
104.1 × 78.7 mm72 parts2LMIT0STM32
Pcb com erros
gabrielgomes16
92.2 × 51.9 mm52 parts2LNo license0MuKOB / RPi / USB - K&S IF MkV
MorseKOB
103 × 59.6 mm59 parts2LMIT0MuKOB-Key & Sounder Interface, MKOB4 USB Interface
MorseKOB
104.1 × 78.7 mm48 parts2LMIT0
How designs wire the LM393DR
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the LM393DR connects to, and the resistors, capacitors and other passives placed on it.
- The 1OUT pin has a pull-up to 3.3V on 8 of 13 designs, most often 10 kΩ (then 1 MΩ).
- The 1IN+ pin has a series resistor on 8 of 13 designs, most often 100 kΩ (then 1 MΩ).
- The 1OUT pin has a series resistor on 6 of 13 designs, most often 1 MΩ (then 100 kΩ).
- The 2IN+ pin has a series resistor on 6 of 13 designs, most often 10 kΩ (then 1 MΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1OUTpin 1 | Connected to: The microcontroller 38% |
|
| 1IN-pin 2 | Connected to: Signal 77% · VREF_BPS 15% |
|
| 1IN+pin 3 | Connected to: Signal 69% · not connected 15% · VREF_G 15% |
|
| GNDpin 4 | Connected to: GND 85% · a signal 15% | — |
| 2IN+pin 5 | Connected to: A connector 23% · VREF_H 23% |
|
| 2IN-pin 6 | Connected to: Signal 69% · 3.3V 23% |
|
| 2OUTpin 7 | Connected to: Signal 69% · not connected 31% |
|
| VCCpin 8 | Connected to: 3.3V 69% · a signal 31% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Digirig icom by 1vers1on, Nova pcb v6 power v2 by Ace2932, Flyback-Driver by Operationorange01 and HolyGrail by whbCool.
The LM393DR in open source designs
The gallery holds 19 open source boards using the LM393DR from 13 GitHub repositories; a typical one measures about 104.1 × 73.9 mm and carries around 72 components.
79% are two-layer designs, the rest use four layers or more, and 53% carry an open source license.
The most starred is HolyGrail by whbCool.
Parts used alongside the LM393DR
Microcontrollers on boards using the LM393DR
What boards using the LM393DR are built for
LM393DR: common questions
Where can I find a LM393DR reference design?
Each of the 19 boards on this page is a real design using the LM393DR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the LM393DR 1OUT pin?
The 1OUT pin has a pull-up to 3.3V on 8 of 13 designs, most often 10 kΩ (then 1 MΩ). Counted from the KiCad layouts of 13 open source designs using the LM393DR.
What resistor goes on the LM393DR 1IN+ pin?
The 1IN+ pin has a series resistor on 8 of 13 designs, most often 100 kΩ (then 1 MΩ). Counted from the KiCad layouts of 13 open source designs using the LM393DR.
What resistor goes on the LM393DR 2IN+ pin?
The 2IN+ pin has a series resistor on 6 of 13 designs, most often 10 kΩ (then 1 MΩ). Counted from the KiCad layouts of 13 open source designs using the LM393DR.
What parts are used alongside the LM393DR?
The AP2112K-3.3, USBLC6-2SC6 and W5500 appear in the most repositories here.
Which microcontrollers do boards using the LM393DR use?
Most are built on ESP32 (7), STM32 (2) and RP2040/RP2350 (1).
How big is a typical board using the LM393DR?
The median is 104.1 × 73.9 mm, and 79% are two-layer designs.
What is the most popular open source board using the LM393DR?
By GitHub stars, HolyGrail by whbCool, with 1 stars.
Can I simulate one of these boards using the LM393DR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.