11 open source boards using the LMV358IDR
Real designs built with the LMV358IDR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
ZXEVO.1010
UzixLS
100 × 100 mm242 parts2LNo license24ESP8266
ZXUNO.1010
UzixLS
100 × 100 mm215 parts2LMIT23ESP32
ESP32indEVB
gmarocco
99.2 × 94.2 mm194 parts4LNo license4Module
KAVIRAJec
83.8 × 61 mm89 parts2LNo license2DSP-Regulator-RevC
Phil-CIA
100 × 125 mm226 parts2LNo license0RP2040/RP2350
MTR Charger X5S
MoreThanRobotsFR
92.6 × 85.3 mm115 parts2LNo license0Cymatics
pdxnpk
70 × 70 mm86 parts2LNo license0MICROPHONE
waxters-osu
43.1 × 21.6 mm22 parts2LNo license0SPEAKER
waxters-osu
40.2 × 36.1 mm22 parts2LNo license0- schematic only · 59 partsSTM32
ProPrj ADC读取 2025-05-24
shydql
59 parts2LGPL-3.00 DSP-Regulator-RevB
Phil-CIA
100 × 100 mm88 parts2LNo license0
How designs wire the LMV358IDR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LMV358IDR connects to, and the resistors, capacitors and other passives placed on it.
- The + pins have a resistor to GND on 6 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The V+ pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 µF).
- The V- pin is tied to GND on 6 of 7 designs.
- The OUT_A pin has a series resistor on 4 of 7 designs, most often 8.2 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT_Apin 1 | Connected to: A connector 29% |
|
| -pin 2, 6 | Connected to: A connector 23% |
|
| +pin 3, 5 | Connected to: Signal 93% |
|
| V-pin 4 | Connected to: GND 86% | — |
| OUT_Bpin 7 | Connected to: Signal 100% |
|
| V+pin 8 | Connected to: 3.3V 83% · a signal 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ZXEVO.1010 by UzixLS, ZXUNO.1010 by UzixLS, ESP32indEVB by gmarocco and Module by KAVIRAJec.
The LMV358IDR in open source designs
The gallery holds 11 open source boards using the LMV358IDR from 9 GitHub repositories; a typical one measures about 95.9 × 89.7 mm and carries around 89 components.
91% are two-layer designs, the rest use four layers or more, and 18% carry an open source license.
The most starred is ZXEVO.1010 by UzixLS.
Parts used alongside the LMV358IDR
Microcontrollers on boards using the LMV358IDR
What boards using the LMV358IDR are built for
LMV358IDR: common questions
Where can I find a LMV358IDR reference design?
Each of the 11 boards on this page is a real design using the LMV358IDR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LMV358IDR + pin?
The + pins have a resistor to GND on 6 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the LMV358IDR.
What decoupling capacitors do designs use on the LMV358IDR V+ pin?
The V+ pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the LMV358IDR.
How is the LMV358IDR V- pin connected?
The V- pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the LMV358IDR.
Which microcontrollers do boards using the LMV358IDR use?
Most are built on AVR/Arduino (1), ESP32 (1), ESP8266 (1) and RP2040/RP2350 (1).
How big is a typical board using the LMV358IDR?
The median is 95.9 × 89.7 mm, and 91% are two-layer designs.
What is the most popular open source board using the LMV358IDR?
By GitHub stars, ZXEVO.1010 by UzixLS, with 24 stars.
Can I simulate one of these boards using the LMV358IDR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.