8 open source boards using the LT1054
Real designs built with the LT1054, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Iosefka motherboard
GlobalSequence
213 × 128.5 mm122 parts2LNo license5AVR/Arduino
OpenXstim
MonzurulAlam
69 × 53.7 mm55 parts2LNo license5AutoPLC
dezamora98
208.9 × 119.9 mm358 parts2LNo license2Peoples permacomputer
genossen
208.3 × 146.1 mm121 parts2LCustom license2STM32
Stm32-fpga oscilloscope
HexFud
160 × 100 mm115 parts4LNo license0- schematic only · 57 partsRP2040/RP2350
Archive fuzz
ravinder-Olivier
57 partsNo license0 Iosefka controlboard
GlobalSequence
213 × 128.5 mm74 parts2LNo license5AVR/Arduino
OpenExoStim
MonzurulAlam
69 × 53.7 mm49 parts2LNo license5
How designs wire the LT1054
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LT1054 connects to, and the resistors, capacitors and other passives placed on it.
- The GPB1 pin has a series capacitor on 4 of 5 designs, most often 10 µF (then 100 µF).
- The GPB3 pin has a series capacitor on 4 of 5 designs, most often 10 µF (then 100 µF).
- The GPB0 pin is left unconnected on 4 of 5 designs.
- The GPB5 pin is left unconnected on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GPB0pin 1 | Connected to: Not connected 80% · a signal 20% | — |
| GPB1pin 2 | Connected to: Signal 100% |
|
| GPB2pin 3 | Connected to: GND 60% · VIN_GND 20% · a signal 20% | — |
| GPB3pin 4 | Connected to: Signal 100% |
|
| GPB4pin 5 | Connected to: -5V 60% · a signal 40% | — |
| GPB5pin 6 | Connected to: Not connected 80% · a signal 20% | — |
| GPB6pin 7 | Connected to: Not connected 80% · a signal 20% | — |
| GPB7pin 8 | Connected to: 5V 80% · a signal 20% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Iosefka controlboard by GlobalSequence, OpenExoStim by MonzurulAlam, AutoPLC by dezamora98 and Peoples permacomputer by genossen.
The LT1054 in open source designs
The gallery holds 8 open source boards using the LT1054 from 6 GitHub repositories; a typical one measures about 208.3 × 119.9 mm and carries around 95 components.
86% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is Iosefka motherboard by GlobalSequence.
Parts used alongside the LT1054
Microcontrollers on boards using the LT1054
What boards using the LT1054 are built for
LT1054: common questions
Where can I find a LT1054 reference design?
Each of the 8 boards on this page is a real design using the LT1054. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LT1054 GPB1 pin connected?
The GPB1 pin has a series capacitor on 4 of 5 designs, most often 10 µF (then 100 µF). Counted from the KiCad layouts of 5 open source designs using the LT1054.
How is the LT1054 GPB3 pin connected?
The GPB3 pin has a series capacitor on 4 of 5 designs, most often 10 µF (then 100 µF). Counted from the KiCad layouts of 5 open source designs using the LT1054.
How is the LT1054 GPB0 pin connected?
The GPB0 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LT1054.
Which microcontrollers do boards using the LT1054 use?
Most are built on AVR/Arduino (2), RP2040/RP2350 (2) and STM32 (1).
How big is a typical board using the LT1054?
The median is 208.3 × 119.9 mm, and 86% are two-layer designs.
What is the most popular open source board using the LT1054?
By GitHub stars, Iosefka motherboard by GlobalSequence, with 5 stars.
Can I simulate one of these boards using the LT1054 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.