11 open source boards using the MCP9700AT-ETT
Real designs built with the MCP9700AT-ETT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Otter-Iron
Jana-Marie
84 × 10 mm63 parts4LGPL-3.0520STM32
OtterIron Devkit
Jana-Marie
28 × 30 mm67 parts2LNo license321MCP39F521 Breakout
whatnick
35.6 × 27.9 mm31 parts2LTAPR-OHL-1.06STM32
OPS
Jana-Marie
49 × 34 mm98 parts2LNo license3ValTronix-VTM0001-EnergyMonitor
vmarzlin
100 × 100 mm111 parts2LGPL-3.01RTB C12
git4dcc
90.3 × 26.6 mm93 parts4LApache-2.01ESP32
ESP32-IoT-Board
ollieelliot
23.9 × 27.2 mm50 parts4LNo license1AVR/Arduino
ProyekKedaireka SHMS Bridge
farisalimmirzani365
100 × 100 mm221 parts2LNo license0STM32
Sdrac electronics
X-Lemon-X
81 × 51 mm142 parts4LNo license0STM32
Stm32f070-board
suyashsingh
69.6 × 31.5 mm40 parts2LNo license0STM32
OtterIron PRO Bot
Jana-Marie
50 × 20.5 mm43 parts2LNo license321
How designs wire the MCP9700AT-ETT
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the MCP9700AT-ETT connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 7 of 10 designs, most often 100 nF (then 1 µF).
- The VOUT pin has a series resistor on 5 of 10 designs, most often 2.37 kΩ (then 5.1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 100% |
|
| VOUTpin 2 | Connected to: The microcontroller 30% |
|
| GNDpin 3 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Otter-Iron by Jana-Marie, OtterIron Devkit by Jana-Marie, MCP39F521 Breakout by whatnick and OPS by Jana-Marie.
The MCP9700AT-ETT in open source designs
The gallery holds 11 open source boards using the MCP9700AT-ETT from 10 GitHub repositories; a typical one measures about 69.6 × 30 mm and carries around 67 components.
64% are two-layer designs, the rest use four layers or more, and 36% carry an open source license.
The most starred is Otter-Iron by Jana-Marie.
Parts used alongside the MCP9700AT-ETT
Microcontrollers on boards using the MCP9700AT-ETT
What boards using the MCP9700AT-ETT are built for
MCP9700AT-ETT: common questions
Where can I find a MCP9700AT-ETT reference design?
Each of the 11 boards on this page is a real design using the MCP9700AT-ETT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP9700AT-ETT VDD pin?
The VDD pin has a decoupling capacitor on 7 of 10 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 10 open source designs using the MCP9700AT-ETT.
What resistor goes on the MCP9700AT-ETT VOUT pin?
The VOUT pin has a series resistor on 5 of 10 designs, most often 2.37 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 10 open source designs using the MCP9700AT-ETT.
What parts are used alongside the MCP9700AT-ETT?
The AP2204R-3.3, OPA340NA, SI8540, STUSB4500QTR and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the MCP9700AT-ETT use?
Most are built on STM32 (6), AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the MCP9700AT-ETT?
The median is 69.6 × 30 mm, and 64% are two-layer designs.
What is the most popular open source board using the MCP9700AT-ETT?
By GitHub stars, Otter-Iron by Jana-Marie, with 520 stars.
Can I simulate one of these boards using the MCP9700AT-ETT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.