7 open source boards using the SI8540
Real designs built with the SI8540, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Otter-Iron
Jana-Marie
84 × 10 mm63 parts4LGPL-3.0520STM32
OtterIron Devkit
Jana-Marie
28 × 30 mm67 parts2LNo license321STM32
Pcbtc
lucysrausch
100 × 100 mm96 parts2LNo license223STM32
Usb c otter
lucysrausch
42.4 × 16 mm43 parts4LCERN-OHL-1.26STM32
OPS
Jana-Marie
49 × 34 mm98 parts2LNo license3STM32
BobinaTeslaMusical
MarcoBravoG
100 × 100 mm96 parts2LGPL-3.00STM32
OtterIron PRO Bot
Jana-Marie
50 × 20.5 mm43 parts2LNo license321
How designs wire the SI8540
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SI8540 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a resistor to GND on 6 of 6 designs, most often 2.37 kΩ (then 2 kΩ).
- The OUT pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 1 nF).
- The RG2 pin has a series resistor on 6 of 6 designs, most often 33 Ω (then 15 Ω).
- The RG1 pin has a pull-up to VBUS on 5 of 6 designs, most often 33 Ω (then 15 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RG1pin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| SHDNpin 3 | Connected to: GND 100% | — |
| OUTpin 4 | Connected to: The microcontroller 100% |
|
| RG2pin 5 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Otter-Iron by Jana-Marie, OtterIron Devkit by Jana-Marie, Pcbtc by lucysrausch and Usb c otter by lucysrausch.
The SI8540 in open source designs
The gallery holds 7 open source boards using the SI8540 from 6 GitHub repositories; a typical one measures about 50 × 30 mm and carries around 67 components.
71% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is Otter-Iron by Jana-Marie.
Parts used alongside the SI8540
Microcontrollers on boards using the SI8540
What boards using the SI8540 are built for
SI8540: common questions
Where can I find a SI8540 reference design?
Each of the 7 boards on this page is a real design using the SI8540. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the SI8540 OUT pin?
The OUT pin has a resistor to GND on 6 of 6 designs, most often 2.37 kΩ (then 2 kΩ). Counted from the KiCad layouts of 6 open source designs using the SI8540.
What resistor goes on the SI8540 RG2 pin?
The RG2 pin has a series resistor on 6 of 6 designs, most often 33 Ω (then 15 Ω). Counted from the KiCad layouts of 6 open source designs using the SI8540.
What pull-up resistor is used on the SI8540 RG1 pin?
The RG1 pin has a pull-up to VBUS on 5 of 6 designs, most often 33 Ω (then 15 Ω). Counted from the KiCad layouts of 6 open source designs using the SI8540.
What parts are used alongside the SI8540?
The AP2204R-3.3, USBLC6-4SC6, MCP9700AT-ETT, OPA340NA and STM32F072C8Ux appear in the most repositories here.
Which microcontrollers do boards using the SI8540 use?
Most are built on STM32 (7).
How big is a typical board using the SI8540?
The median is 50 × 30 mm, and 71% are two-layer designs.
What is the most popular open source board using the SI8540?
By GitHub stars, Otter-Iron by Jana-Marie, with 520 stars.
Can I simulate one of these boards using the SI8540 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.