7 open source boards using the ME6211
Real designs built with the ME6211, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
CLN-ClosedLoopNemaDriver
creapunk
38 × 39 mm89 parts4LCC-BY-NC-4.01.1kESP32
EsPiFF
MDCservice
83.5 × 56 mm168 parts6LGPL-3.0224Raspberry Pi
Rp2350 stamp xl hw
solderparty
45 × 25 mm41 parts4LCERN-OHL-1.243UINIO-Monitor
uinika
100 × 77.9 mm63 parts2LNo license12ESP32
RC vel car
surya-shreevathsa11
46 × 32 mm70 parts4LNo license0RP2040/RP2350
Funkyboi
Jameswill-Winsock
51 × 30 mm51 parts4LNo license0ESP32
RC vel controller
surya-shreevathsa11
85 × 57.8 mm58 parts4LNo license0
How designs wire the ME6211
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ME6211 connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a decoupling capacitor on 4 of 6 designs, most often 1 µF (then 10 µF).
- The VOUT pin has a decoupling capacitor on 4 of 5 designs, most often 10 µF (then 1 µF).
- The EN pin has a capacitor to GND on 3 of 6 designs, most often 10 µF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: VIN 67% · GND 17% · a signal 17% |
|
| GNDpin 2 | Connected to: GND 83% · 3.3V 17% | — |
| ENpin 3 | Connected to: A connector 50% · 5V 33% |
|
| NCpin 4 | Connected to: Not connected 100% | — |
| VOUTpin 5 | Connected to: 3.3V 80% · a signal 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CLN-ClosedLoopNemaDriver by creapunk, EsPiFF by MDCservice, Rp2350 stamp xl hw by solderparty and UINIO-Monitor by uinika.
The ME6211 in open source designs
The gallery holds 7 open source boards using the ME6211 from 6 GitHub repositories; a typical one measures about 51 × 39 mm and carries around 63 components.
86% use four copper layers or more, and 29% carry an open source license.
The most starred is CLN-ClosedLoopNemaDriver by creapunk.
Parts used alongside the ME6211
Microcontrollers on boards using the ME6211
What boards using the ME6211 are built for
ME6211: common questions
Where can I find a ME6211 reference design?
Each of the 7 boards on this page is a real design using the ME6211. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ME6211 VIN pin?
The VIN pin has a decoupling capacitor on 4 of 6 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the ME6211.
What decoupling capacitors do designs use on the ME6211 VOUT pin?
The VOUT pin has a decoupling capacitor on 4 of 5 designs, most often 10 µF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the ME6211.
How is the ME6211 EN pin connected?
The EN pin has a capacitor to GND on 3 of 6 designs, most often 10 µF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the ME6211.
Which microcontrollers do boards using the ME6211 use?
Most are built on ESP32 (3), Raspberry Pi (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the ME6211?
The median is 51 × 39 mm, and 14% are two-layer designs.
What is the most popular open source board using the ME6211?
By GitHub stars, CLN-ClosedLoopNemaDriver by creapunk, with 1,101 stars.
Can I simulate one of these boards using the ME6211 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.