6 open source boards using the MIC29302WU

Real designs built with the MIC29302WU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the MIC29302WU

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MIC29302WU connects to, and the resistors, capacitors and other passives placed on it.

  • The VIN pin has a capacitor to GND on 4 of 5 designs, most often 10 µF (then 100 nF).
  • The VOUT pin has a capacitor to GND on 3 of 5 designs, most often 10 µF (then 100 nF).
  • The ADJ pin has a pull-up to 3.3V on 3 of 5 designs, most often 3.6 kΩ (then 2.4 kΩ).
  • The ADJ pin has a resistor to GND on 3 of 5 designs, most often 1 kΩ (then 1.2 kΩ).
ENpin 1Connected to: Signal 40% · not connected 20% · GND 20% · 5V 20%
  • Capacitor to GND on 40% · 10 µF (1), 100 µF (1), 22 µF (1)
VINpin 2Connected to: Signal 60% · 3.3V 40%
  • Capacitor to GND on 80% · 10 µF (5), 100 nF (2), 100 µF (2)
  • Series resistor on 40% · 10 Ω (1), 10 mΩ (1), 10 kΩ (1)
GNDpin 3Connected to: GND 86%
VOUTpin 4Connected to: Signal 60% · 5V 40%
  • Capacitor to GND on 60% · 10 µF (2), 100 nF (2), 22 µF (1)
  • Series resistor on 40% · 9.2 kΩ (1), 10 mΩ (1), 5.1 kΩ (1)
ADJpin 5Connected to: Signal 100%
  • Pull-up to 3.3V on 60% · 3.6 kΩ (1), 2.4 kΩ (1)
  • Resistor to GND on 60% · 1 kΩ (2), 1.2 kΩ (1)
  • Series resistor on 40% · 9.2 kΩ (1), 1.56 kΩ (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Access controller by physiii, OverHead v1 by stefanofinetti, Comm Board by cristobalcuevas and Ampere by LtBrain.

The MIC29302WU in open source designs

The gallery holds 6 open source boards using the MIC29302WU from 5 GitHub repositories; a typical one measures about 140 × 95 mm and carries around 197 components.

67% use four copper layers or more, and 50% carry an open source license.

The most starred is Access controller by physiii.

Parts used alongside the MIC29302WU

Microcontrollers on boards using the MIC29302WU

MIC29302WU: common questions

Where can I find a MIC29302WU reference design?

Each of the 6 boards on this page is a real design using the MIC29302WU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MIC29302WU VIN pin connected?

The VIN pin has a capacitor to GND on 4 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the MIC29302WU.

How is the MIC29302WU VOUT pin connected?

The VOUT pin has a capacitor to GND on 3 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the MIC29302WU.

What pull-up resistor is used on the MIC29302WU ADJ pin?

The ADJ pin has a pull-up to 3.3V on 3 of 5 designs, most often 3.6 kΩ (then 2.4 kΩ). Counted from the KiCad layouts of 5 open source designs using the MIC29302WU.

Which microcontrollers do boards using the MIC29302WU use?

Most are built on AVR/Arduino (2), ESP32 (1), RP2040/RP2350 (1) and STM32 (1).

How big is a typical board using the MIC29302WU?

The median is 140 × 95 mm, and 33% are two-layer designs.

What is the most popular open source board using the MIC29302WU?

By GitHub stars, Access controller by physiii, with 13 stars.

Can I simulate one of these boards using the MIC29302WU before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part