9 open source boards using the MICRO-B_USB
Real designs built with the MICRO-B_USB, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
PIP-WATCH ZERO
jsyk
80 × 35 mm74 parts2LNo license11NXP
Runner s-GPS
dbtayl
79.9 × 50.8 mm38 parts2LBSD-3-Clause11Microchip SAM
SensebenderGW
mysensors
50 × 50 mm70 parts2LNo license7ESP8266
GPIB-wifi
bitdivision
63 × 65.7 mm105 parts2LNo license4Sk8flair
myronww
50 × 3 mm80 parts2LNo license0STM32
PIP-WATCH ZERO
vpreethamkashyap
80 × 35 mm74 parts2LNo license0NXP
Radio
cculpepper
40.9 × 25 mm89 parts4LNo license4TI MSP430/CC
CDHS
skycan
50 × 50 mm44 parts2LCustom license0Skycan eps
skycan
50 × 50 mm36 parts2LCustom license0
How designs wire the MICRO-B_USB
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the MICRO-B_USB connects to, and the resistors, capacitors and other passives placed on it.
- Pin 4 is left unconnected on 7 of 8 designs.
- Pin 5 is tied to GND on 6 of 8 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: MCP73831 25%, USB6BX 25% |
|
| Pin 4 | Connected to: Not connected 88% | — |
| Pin 5 | Connected to: GND 75% · a signal 25% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Runner s-GPS by dbtayl, PIP-WATCH ZERO by jsyk, SensebenderGW by mysensors and GPIB-wifi pcb by bitdivision.
The MICRO-B_USB in open source designs
The gallery holds 9 open source boards using the MICRO-B_USB from 8 GitHub repositories; a typical one measures about 50 × 50 mm and carries around 74 components.
89% are two-layer designs, the rest use four layers or more, and 11% carry an open source license.
The most starred is PIP-WATCH ZERO by jsyk.
Parts used alongside the MICRO-B_USB
Microcontrollers on boards using the MICRO-B_USB
What boards using the MICRO-B_USB are built for
MICRO-B_USB: common questions
Where can I find a MICRO-B_USB reference design?
Each of the 9 boards on this page is a real design using the MICRO-B_USB. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MICRO-B_USB pin 4 connected?
Pin 4 is left unconnected on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the MICRO-B_USB.
How is the MICRO-B_USB pin 5 connected?
Pin 5 is tied to GND on 6 of 8 designs (a signal on 2). Counted from the KiCad layouts of 8 open source designs using the MICRO-B_USB.
What parts are used alongside the MICRO-B_USB?
The MCP73831, BTM431, LD59015C33R, STM32F103RXT and USB6BX appear in the most repositories here.
Which microcontrollers do boards using the MICRO-B_USB use?
Most are built on NXP (2), STM32 (2), ESP8266 (1) and Microchip SAM (1).
How big is a typical board using the MICRO-B_USB?
The median is 50 × 50 mm, and 89% are two-layer designs.
What is the most popular open source board using the MICRO-B_USB?
By GitHub stars, PIP-WATCH ZERO by jsyk, with 11 stars.
Can I simulate one of these boards using the MICRO-B_USB before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.