9 open source boards using the MMC5633NJL
Real designs built with the MMC5633NJL, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
ExAce Expansion Card Accelerator
cdg66
24 × 27.3 mm180 parts8LCC-BY-4.037Raspberry Pi
Unfolding space hardware
jakobkilian
57 × 74.6 mm82 parts2LCC-BY-4.05STM32
Flight-Computer
Pioneer-Rocketry
30 × 60 mm100 parts6LNo license2RP2040/RP2350
Dev real
iamdarshg
105 × 105 mm310 parts4LNo license1EnchantiW106
aburt2
62.2 × 25.4 mm61 parts2LMIT1RP2040/RP2350
FligthComputers
ManuelRao
50 × 72.5 mm131 parts4LNo license0ESP32
MiniBot
DDeGonge
21.2 × 28 mm58 parts4LMIT40STM32
FiberCircuits - MCU & sensing fiber
FiberCircuits
200 × 4.4 mm18 parts2LNo license8RP2040/RP2350
Dev real production
iamdarshg
105 × 105 mm310 parts4LNo license1
How designs wire the MMC5633NJL
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the MMC5633NJL connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 7 of 8 designs, most often 5.1 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 7 of 8 designs, most often 5.1 kΩ (then 4.7 kΩ).
- The VSA pin is tied to GND on 8 of 8 designs.
- The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSApin A1 | Connected to: GND 100% | — |
| SCLpin A2 | Connected to: The microcontroller 63% |
|
| VDDpin B1 | Connected to: 3.3V 100% |
|
| SDApin B2 | Connected to: The microcontroller 63% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MiniBot by DDeGonge, ExAce Expansion Card Accelerator by cdg66, FiberCircuits - MCU & sensing fiber by FiberCircuits and Unfolding space hardware by jakobkilian.
The MMC5633NJL in open source designs
The gallery holds 9 open source boards using the MMC5633NJL from 8 GitHub repositories; a typical one measures about 57 × 60 mm and carries around 100 components.
67% use four copper layers or more, and 44% carry an open source license.
The most starred is MiniBot by DDeGonge.
Parts used alongside the MMC5633NJL
Microcontrollers on boards using the MMC5633NJL
What boards using the MMC5633NJL are built for
MMC5633NJL: common questions
Where can I find a MMC5633NJL reference design?
Each of the 9 boards on this page is a real design using the MMC5633NJL. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MMC5633NJL SCL pin?
The SCL pin has a pull-up to 3.3V on 7 of 8 designs, most often 5.1 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 8 open source designs using the MMC5633NJL.
What pull-up resistor is used on the MMC5633NJL SDA pin?
The SDA pin has a pull-up to 3.3V on 7 of 8 designs, most often 5.1 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 8 open source designs using the MMC5633NJL.
How is the MMC5633NJL VSA pin connected?
The VSA pin is tied to GND on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the MMC5633NJL.
Which microcontrollers do boards using the MMC5633NJL use?
Most are built on RP2040/RP2350 (3), STM32 (3), ESP32 (1) and Raspberry Pi (1).
How big is a typical board using the MMC5633NJL?
The median is 57 × 60 mm, and 33% are two-layer designs.
What is the most popular open source board using the MMC5633NJL?
By GitHub stars, MiniBot by DDeGonge, with 40 stars.
Can I simulate one of these boards using the MMC5633NJL before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.