9 open source boards using the OPA354
Real designs built with the OPA354, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Plate EC
calvin-mcd
245.7 × 83.6 mm147 parts4LCC-BY-NC-4.07STM32
Ampersand
calvin-mcd
257.2 × 76.2 mm40 parts2LGPL-3.06STM32
Capybully
sporkus
257.2 × 89.2 mm36 parts4LCERN-OHL-W-2.018STM32
Forti EC
calvin-mcd
245.7 × 82.9 mm123 parts4LCC-BY-NC-4.07ERQ15 11-6060-SiPM
Maniak003
14 × 14 mm16 parts2LGPL-3.026STM32
Numbpad
calvin-mcd
76 × 76.5 mm33 parts4LCC-BY-NC-4.016ADC-B-v1
macaba
20.5 × 10.5 mm12 parts4LMIT94STM32
Forti rev 3
calvin-mcd
245.7 × 82.9 mm66 parts2LCC-BY-NC-4.07STM32
Forti rev 4
calvin-mcd
245.7 × 82.9 mm66 parts2LCC-BY-NC-4.07
How designs wire the OPA354
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the OPA354 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 6 designs, most often 100 kΩ (then 22 Ω).
- The - pin has a series resistor on 6 of 6 designs, most often 100 kΩ (then 22 Ω).
- The V+ pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF).
- The V- pin is tied to GND on 6 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 67% |
|
| V-pin 2 | Connected to: GND 100% | — |
| +pin 3 | Connected to: 74HC4051 67%, the microcontroller 67% |
|
| -pin 4 | Connected to: Signal 100% |
|
| V+pin 5 | Connected to: 3.3V 83% · a signal 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ADC-B-v1 by macaba, ERQ15 11-6060-SiPM by Maniak003, Capybully by sporkus and Numbpad by calvin-mcd.
The OPA354 in open source designs
The gallery holds 9 open source boards using the OPA354 from 6 GitHub repositories; a typical one measures about 245.6 × 82.9 mm and carries around 40 components.
56% use four copper layers or more, and 44% carry an open source license.
The most starred is ADC-B-v1 by macaba.
Parts used alongside the OPA354
Microcontrollers on boards using the OPA354
What boards using the OPA354 are built for
OPA354: common questions
Where can I find a OPA354 reference design?
Each of the 9 boards on this page is a real design using the OPA354. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPA354 pin 1?
Pin 1 has a series resistor on 6 of 6 designs, most often 100 kΩ (then 22 Ω). Counted from the KiCad layouts of 6 open source designs using the OPA354.
What resistor goes on the OPA354 - pin?
The - pin has a series resistor on 6 of 6 designs, most often 100 kΩ (then 22 Ω). Counted from the KiCad layouts of 6 open source designs using the OPA354.
What decoupling capacitors do designs use on the OPA354 V+ pin?
The V+ pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the OPA354.
What parts are used alongside the OPA354?
The 74HC4051, XC6206PXXXMR-REGULATOR_LINEAR and STM32F072CBT6 appear in the most repositories here.
Which microcontrollers do boards using the OPA354 use?
Most are built on STM32 (7).
How big is a typical board using the OPA354?
The median is 245.6 × 82.9 mm, and 44% are two-layer designs.
What is the most popular open source board using the OPA354?
By GitHub stars, ADC-B-v1 by macaba, with 94 stars.
Can I simulate one of these boards using the OPA354 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.