15 open source boards using the OPAMP
Real designs built with the OPAMP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
VCO
Desval27
160 × 233.4 mm129 parts2LMIT0NuTube MUSES AMP PCB v2
Andrew-Takahashi
100 × 100 mm54 parts2LNo license0RP2040/RP2350
Pi pico guitar tuner
Krovikan-Vamp
56.8 × 139.2 mm50 parts2LBSD-3-Clause0Assignment 3
TefoAM
52.1 × 38.1 mm26 parts4LGPL-3.00Makerspace THT Workshop
Austin-K-Nguyen
123.3 × 94.8 mm19 parts2LNo license0Non inverting amplifier
uw-madison-chem-shops
61 × 35.6 mm8 parts2LNo license0- schematic only · 17 parts
Eeaic-2022-pll
Keriz
17 partsNo license0 Photodiode
space-technologies-at-california
25.4 × 15.2 mm6 parts2LNo license1VC-LFOs
Desval27
160 × 100 mm92 parts2LMIT0RefPhotoDiode MDversion1.2
LeonAbelmann
33.4 × 33.4 mm14 parts2LMIT1RefPhotoDiode MDversion1.2
CameronBrooks11
33.4 × 33.4 mm14 parts2LMIT0PHASE-SHIFTER
Desval27
160 × 100 mm79 parts2LMIT0ADSR CONTROLLER
Desval27
160 × 100 mm77 parts2LMIT0RefPhotoDiode MDversion
LeonAbelmann
32.8 × 32.8 mm11 parts2LMIT1RefPhotoDiode MDversion
CameronBrooks11
32.8 × 32.8 mm11 parts2LMIT0
How designs wire the OPAMP
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the OPAMP connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 7 of 9 designs, most often 1 kΩ (then 10 kΩ).
- The - pins have a resistor to GND on 5 of 9 designs, most often 1 kΩ (then 33 kΩ).
- The + pins have a series resistor on 5 of 8 designs, most often 10 kΩ (then 33 kΩ).
- The + pins have a resistor to GND on 4 of 8 designs, most often 1 MΩ (then 10 MΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NULL_1pin 1 | Connected to: Signal 44% · not connected 22% · GND 33% |
|
| -pin 2, 6 | Connected to: Signal 80% |
|
| +pin 3, 5 | Connected to: Signal 63% · GND 25% |
|
| V-pin 4 | Connected to: -15V 50% · a signal 38% |
|
| V+_7pin 7 | Connected to: Not connected 33% · 15V 33% · a signal 33% |
|
| V+pin 8 | Connected to: Not connected 67% · 3V 17% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RefPhotoDiode MDversion by LeonAbelmann, Photodiode by space-technologies-at-california, NuTube MUSES AMP PCB v2 by Andrew-Takahashi and Makerspace THT Workshop by Austin-K-Nguyen.
The OPAMP in open source designs
The gallery holds 15 open source boards using the OPAMP from 10 GitHub repositories; a typical one measures about 58.9 × 66.4 mm and carries around 19 components.
93% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is RefPhotoDiode MDversion1.2 by LeonAbelmann.
Parts used alongside the OPAMP
Microcontrollers on boards using the OPAMP
What boards using the OPAMP are built for
OPAMP: common questions
Where can I find a OPAMP reference design?
Each of the 15 boards on this page is a real design using the OPAMP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPAMP - pin?
The - pins have a series resistor on 7 of 9 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 9 open source designs using the OPAMP.
What resistor goes on the OPAMP + pin?
The + pins have a series resistor on 5 of 8 designs, most often 10 kΩ (then 33 kΩ). Counted from the KiCad layouts of 9 open source designs using the OPAMP.
What decoupling capacitors do designs use on the OPAMP V- pin?
The V- pin has a decoupling capacitor on 4 of 8 designs, most often 1 µF (then 100 µF). Counted from the KiCad layouts of 9 open source designs using the OPAMP.
Which microcontrollers do boards using the OPAMP use?
Most are built on RP2040/RP2350 (1).
How big is a typical board using the OPAMP?
The median is 58.9 × 66.4 mm, and 93% are two-layer designs.
What is the most popular open source board using the OPAMP?
By GitHub stars, RefPhotoDiode MDversion1.2 by LeonAbelmann, with 1 stars.
Can I simulate one of these boards using the OPAMP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.