6 open source boards using the PLT133_T10W
Real designs built with the PLT133_T10W, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FreeDSP-OCTAVIA
freeDSP
178 × 99 mm505 parts4LCC-BY-SA-4.019FreeDSPx-ADAT-IO-x4
freeDSP
100 × 100 mm114 parts2LNo license10FreeDSP-G
freeDSP
170 × 101 mm367 parts4LCC0-1.06FPGA
ZynqBoard
tamapochi1
136.8 × 79 mm284 parts6LNo license2FPGA
ZynqBoard2
tamapochi1
89 × 69 mm284 parts6LNo license2ESP32
Jlr most amp
Oleg-mk
120.1 × 58.6 mm147 parts4LCERN-OHL-S-2.01
How designs wire the PLT133_T10W
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the PLT133_T10W connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 is tied to 3.3V on 5 of 5 designs.
- Pin 3 is tied to GND on 5 of 5 designs.
- Pin 1 has a series resistor on 4 of 5 designs, most often 47 Ω (then 68 Ω).
- Pin 2 has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: 3.3V 100% |
|
| Pin 3 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FreeDSP-OCTAVIA by freeDSP, FreeDSPx-ADAT-IO-x4 by freeDSP, FreeDSP-G by freeDSP and ZynqBoard by tamapochi1.
The PLT133_T10W in open source designs
The gallery holds 6 open source boards using the PLT133_T10W from 5 GitHub repositories; a typical one measures about 128.4 × 89 mm and carries around 284 components.
83% use four copper layers or more, and 50% carry an open source license.
The most starred is FreeDSP-OCTAVIA by freeDSP.
Parts used alongside the PLT133_T10W
What boards using the PLT133_T10W are built for
PLT133_T10W: common questions
Where can I find a PLT133_T10W reference design?
Each of the 6 boards on this page is a real design using the PLT133_T10W. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the PLT133_T10W pin 2 connected?
Pin 2 is tied to 3.3V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the PLT133_T10W.
How is the PLT133_T10W pin 3 connected?
Pin 3 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the PLT133_T10W.
What resistor goes on the PLT133_T10W pin 1?
Pin 1 has a series resistor on 4 of 5 designs, most often 47 Ω (then 68 Ω). Counted from the KiCad layouts of 5 open source designs using the PLT133_T10W.
What parts are used alongside the PLT133_T10W?
The PLR135-T10, 74LVC1G04, AMS1117-3.3 and TPS5430DDA appear in the most repositories here.
Which microcontrollers do boards using the PLT133_T10W use?
Most are built on FPGA (2) and ESP32 (1).
How big is a typical board using the PLT133_T10W?
The median is 128.4 × 89 mm, and 17% are two-layer designs.
What is the most popular open source board using the PLT133_T10W?
By GitHub stars, FreeDSP-OCTAVIA by freeDSP, with 19 stars.
Can I simulate one of these boards using the PLT133_T10W before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.