7 open source boards using the PLR135-T10
Real designs built with the PLR135-T10, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FreeDSP-OCTAVIA
freeDSP
178 × 99 mm505 parts4LCC-BY-SA-4.019FreeDSPx-ADAT-IO-x4
freeDSP
100 × 100 mm114 parts2LNo license10FreeDSP-G
freeDSP
170 × 101 mm367 parts4LCC0-1.06RISC-V
Kepler x
kunichiko
144 × 150 mm153 parts4LMIT4Teensy toslink receiver
kylemanna
24.9 × 18.3 mm16 parts2LNo license4FPGA
ZynqBoard
tamapochi1
136.8 × 79 mm284 parts6LNo license2FPGA
ZynqBoard2
tamapochi1
89 × 69 mm284 parts6LNo license2
How designs wire the PLR135-T10
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the PLR135-T10 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF).
- The VCC pin has a inductor on 5 of 6 designs, most often 47 µH.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: Signal 83% · 3.3V 17% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| VOUTpin 3 | Connected to: Signal 100% |
|
| NCpin 4, 5 | Connected to: Not connected 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FreeDSP-OCTAVIA by freeDSP, FreeDSPx-ADAT-IO-x4 by freeDSP, FreeDSP-G by freeDSP and Kepler x by kunichiko.
The PLR135-T10 in open source designs
The gallery holds 7 open source boards using the PLR135-T10 from 6 GitHub repositories; a typical one measures about 136.8 × 99 mm and carries around 284 components.
71% use four copper layers or more, and 43% carry an open source license.
The most starred is FreeDSP-OCTAVIA by freeDSP.
Parts used alongside the PLR135-T10
What boards using the PLR135-T10 are built for
PLR135-T10: common questions
Where can I find a PLR135-T10 reference design?
Each of the 7 boards on this page is a real design using the PLR135-T10. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the PLR135-T10 VCC pin connected?
The VCC pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the PLR135-T10.
What parts are used alongside the PLR135-T10?
The PLT133_T10W, 74LVC1G04, 74LVC541A, AMS1117-3.3 and PCM5102A appear in the most repositories here.
Which microcontrollers do boards using the PLR135-T10 use?
Most are built on FPGA (2) and RISC-V (1).
How big is a typical board using the PLR135-T10?
The median is 136.8 × 99 mm, and 29% are two-layer designs.
What is the most popular open source board using the PLR135-T10?
By GitHub stars, FreeDSP-OCTAVIA by freeDSP, with 19 stars.
Can I simulate one of these boards using the PLR135-T10 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.