10 open source boards using the SN65HVD232DR
Real designs built with the SN65HVD232DR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Hw sensor
larus-breeze
120 × 74.6 mm215 parts4LCustom license14ESP32
Motor master
PaulBailey-1
47 × 55.5 mm48 parts2LNo license1STM32
Freyja gcs
aesirkth
300 × 200 mm281 parts4LNo license0STM32
Main interface board
callumsnowden
110 × 55 mm83 parts4LMIT0CW312T-MPC5676R
jmercerr
58.7 × 53.7 mm78 parts2LNo license0STM32
Sigmadrive solo
mstoilov
70.7 × 87.3 mm161 parts4LNo license5ESP32
BIMU V 1
robotique-udes
40 × 35 mm45 parts4LGPL-2.01ESP32
Template
robotique-udes
40 × 35 mm40 parts4LGPL-2.01STM32
Joystick interface board
callumsnowden
60 × 39 mm38 parts2LMIT0STM32
VORTAC YOLO
FoCTow
68.5 × 24.7 mm13 parts4LNo license2
How designs wire the SN65HVD232DR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the SN65HVD232DR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 22 µF).
- The CANH pin has a series resistor on 6 of 8 designs, most often 120 Ω (then 100 Ω).
- The CANL pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 60 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 3 | Connected to: 3.3V 100% |
|
| NCpin 5, 8 | Connected to: Not connected 88% | — |
| CANLpin 6 | Connected to: A connector 88% |
|
| CANHpin 7 | Connected to: A connector 88% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hw sensor by larus-breeze, Sigmadrive solo by mstoilov, VORTAC YOLO by FoCTow and Motor master by PaulBailey-1.
The SN65HVD232DR in open source designs
The gallery holds 10 open source boards using the SN65HVD232DR from 8 GitHub repositories; a typical one measures about 64.2 × 54.3 mm and carries around 63 components.
70% use four copper layers or more, and 40% carry an open source license.
The most starred is Hw sensor by larus-breeze.
Parts used alongside the SN65HVD232DR
What boards using the SN65HVD232DR are built for
SN65HVD232DR: common questions
Where can I find a SN65HVD232DR reference design?
Each of the 10 boards on this page is a real design using the SN65HVD232DR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN65HVD232DR VCC pin?
The VCC pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 8 open source designs using the SN65HVD232DR.
What resistor goes on the SN65HVD232DR CANH pin?
The CANH pin has a series resistor on 6 of 8 designs, most often 120 Ω (then 100 Ω). Counted from the KiCad layouts of 8 open source designs using the SN65HVD232DR.
What resistor goes on the SN65HVD232DR CANL pin?
The CANL pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 60 Ω). Counted from the KiCad layouts of 8 open source designs using the SN65HVD232DR.
Which microcontrollers do boards using the SN65HVD232DR use?
Most are built on STM32 (5) and ESP32 (4).
How big is a typical board using the SN65HVD232DR?
The median is 64.2 × 54.3 mm, and 30% are two-layer designs.
What is the most popular open source board using the SN65HVD232DR?
By GitHub stars, Hw sensor by larus-breeze, with 14 stars.
Can I simulate one of these boards using the SN65HVD232DR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.