11 open source boards using the SN74CB3T3245PWR

Real designs built with the SN74CB3T3245PWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

11 boardsClear filters|Most starred

How designs wire the SN74CB3T3245PWR

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SN74CB3T3245PWR connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 1 µF).
  • The OE pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ.
NCpin 1Connected to: Not connected 83% · GND 17%
GNDpin 10Connected to: GND 100%
OEpin 19Connected to: Signal 60% · GND 40%
  • Pull-up to 3.3V on 40% · 10 kΩ (2)
VCCpin 20Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (3), 1 µF (2)

16 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include NuBusFPGA by MelkhiorVintageComputing, Aqp moda HC by fvdhoef, ASPECT2 by xboxoneresearch and SoMProgrammerNTester by fsnitz.

The SN74CB3T3245PWR in open source designs

The gallery holds 11 open source boards using the SN74CB3T3245PWR from 6 GitHub repositories; a typical one measures about 141 × 89.5 mm and carries around 116 components.

55% use four copper layers or more, and 55% carry an open source license.

The most starred is NuBusFPGA by MelkhiorVintageComputing.

Microcontrollers on boards using the SN74CB3T3245PWR

SN74CB3T3245PWR: common questions

Where can I find a SN74CB3T3245PWR reference design?

Each of the 11 boards on this page is a real design using the SN74CB3T3245PWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the SN74CB3T3245PWR VCC pin?

The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the SN74CB3T3245PWR.

What pull-up resistor is used on the SN74CB3T3245PWR OE pin?

The OE pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the SN74CB3T3245PWR.

Which microcontrollers do boards using the SN74CB3T3245PWR use?

Most are built on ESP32 (5), FPGA (1), Raspberry Pi (1) and STM32 (1).

How big is a typical board using the SN74CB3T3245PWR?

The median is 141 × 89.5 mm, and 45% are two-layer designs.

What is the most popular open source board using the SN74CB3T3245PWR?

By GitHub stars, NuBusFPGA by MelkhiorVintageComputing, with 62 stars.

Can I simulate one of these boards using the SN74CB3T3245PWR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part