12 open source boards using the SN74HC14DR
Real designs built with the SN74HC14DR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
OTTO-Beta-Main
bitfieldaudio
288.5 × 95 mm303 parts4LCC-BY-NC-4.037STM32
VCU
formulaslug
92.5 × 101.6 mm202 parts4LNo license7ESP32
LiF FC-PCB rev1
aventadoro-ish
70 × 90 mm193 parts4LNo license2Cm5-guard-A
anatolbricoham
290 × 280 mm157 parts2LNo license0Cm5-guard-A
Brico-Hams
290 × 280 mm157 parts2LNo license0Glr bspd
green-lion-racing
60 × 90 mm123 parts2LMIT0AVR/Arduino
Ecng4504-maze solver team 5
elshazlio
142.3 × 80.5 mm99 parts4LMIT0LILYGO ESP32 SHIELD
R-Mutura
101 × 54.7 mm47 parts2LNo license0Osc control
Takazudo
316 × 116 mm412 parts4LNo license0Placed prerouted
Brico-Hams
290 × 280 mm157 parts2LNo license0Placed prerouted
anatolbricoham
290 × 280 mm157 parts2LNo license0Osc control routed draft
Takazudo
316 × 116 mm412 parts4LNo license0
How designs wire the SN74HC14DR
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the SN74HC14DR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 1 µF).
- The 1A_1 pin has a capacitor to GND on 5 of 9 designs, most often 100 nF (then 10 nF).
- The 1A_1 pin has a series resistor on 5 of 9 designs, most often 10 kΩ (then 23.9 kΩ).
- The 6A_13 pin has a series resistor on 5 of 9 designs, most often 10 kΩ (then 300 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1A_1pin 1 | Connected to: A connector 33% |
|
| 2A_3pin 3 | Connected to: A connector 33% |
|
| 3A_5pin 5 | Connected to: A connector 33% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| 5A_11pin 11 | Connected to: A connector 44% · GND 22% |
|
| 6A_13pin 13 | Connected to: A connector 33% · GND 22% |
|
| VCCpin 14 | Connected to: 5V 67% · a signal 33% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OTTO-Beta-Main by bitfieldaudio, VCU by formulaslug, LiF FC-PCB rev1 by aventadoro-ish and Cm5-guard-A by anatolbricoham.
The SN74HC14DR in open source designs
The gallery holds 12 open source boards using the SN74HC14DR from 9 GitHub repositories; a typical one measures about 289.3 × 108.8 mm and carries around 157 components.
50% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is OTTO-Beta-Main by bitfieldaudio.
Parts used alongside the SN74HC14DR
Microcontrollers on boards using the SN74HC14DR
What boards using the SN74HC14DR are built for
SN74HC14DR: common questions
Where can I find a SN74HC14DR reference design?
Each of the 12 boards on this page is a real design using the SN74HC14DR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN74HC14DR VCC pin?
The VCC pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the SN74HC14DR.
How is the SN74HC14DR 1A_1 pin connected?
The 1A_1 pin has a capacitor to GND on 5 of 9 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 9 open source designs using the SN74HC14DR.
What resistor goes on the SN74HC14DR 6A_13 pin?
The 6A_13 pin has a series resistor on 5 of 9 designs, most often 10 kΩ (then 300 Ω). Counted from the KiCad layouts of 9 open source designs using the SN74HC14DR.
What parts are used alongside the SN74HC14DR?
The AMS1117-3.3, AP2112K-3.3TRG1, LTV-817S, MCP23017-E/SO and SN74HC08DR appear in the most repositories here.
Which microcontrollers do boards using the SN74HC14DR use?
Most are built on STM32 (2), AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the SN74HC14DR?
The median is 289.3 × 108.8 mm, and 50% are two-layer designs.
What is the most popular open source board using the SN74HC14DR?
By GitHub stars, OTTO-Beta-Main by bitfieldaudio, with 37 stars.
Can I simulate one of these boards using the SN74HC14DR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.