20 open source boards using the SN74HC08DR
Real designs built with the SN74HC08DR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NXP
LegRobotBoardTeensy
01binary
178.2 × 111 mm154 parts2LNo license20AVR/Arduino
MSAP-2 rev.A
mehrantsi
240 × 1056 mm658 parts2LMIT13TC IO REVC
hankenken
100 × 100 mm50 parts2LNo license1Cm5-guard-A
anatolbricoham
290 × 280 mm157 parts2LNo license0Cm5-guard-A
Brico-Hams
290 × 280 mm157 parts2LNo license0- schematic only · 88 partsSTM32
ReefVolt PlugControl — 2ch AC heater carrier
blueacro
88 parts4LCERN-OHL-P-2.00 NXP
MainRobotBoardTeensy
01binary
174.1 × 121.1 mm145 parts2LNo license20AVR/Arduino
MSAP-2 rev.A SMD
mehrantsi
178 × 711 mm658 parts2LMIT13TC IO REVD MINI
hankenken
50 × 40 mm46 parts2LNo license1Placed prerouted
Brico-Hams
290 × 280 mm157 parts2LNo license0Placed prerouted
anatolbricoham
290 × 280 mm157 parts2LNo license0AVR/Arduino
MSAP-2-production
mehrantsi
300 × 248.8 mm520 parts6LMIT13ArmRobotBoardTeensy
01binary
87.5 × 55 mm37 parts2LNo license20AVR/Arduino
MSAP-2-production routed
mehrantsi
300 × 248.8 mm520 parts6LMIT13AVR/Arduino
Pre connector model normalization v1
mehrantsi
300 × 248.8 mm520 parts6LMIT13Bms
IllinoisRoboticsInSpace
36 × 32.7 mm27 parts2LNo license2AVR/Arduino
Pre cpl coordinate fix v1
mehrantsi
300 × 248.8 mm520 parts6LMIT13AVR/Arduino
Pre current source usb keepout repair v1
mehrantsi
300 × 248.8 mm520 parts6LMIT13AVR/Arduino
Pre j5-model alignment route v1
mehrantsi
300 × 248.8 mm520 parts6LMIT13AVR/Arduino
MSAP-2-production source
mehrantsi
300 × 248.8 mm375 parts6LMIT13
How designs wire the SN74HC08DR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SN74HC08DR connects to, and the resistors, capacitors and other passives placed on it.
- The 2Y pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ.
- The 3Y pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ.
- The 4Y pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1Bpin 2 | Connected to: A connector 50%, SN74HC14DR 33% |
|
| 2Bpin 5 | Connected to: MCP23017-E/SO 33% |
|
| 2Ypin 6 | Connected to: Signal 83% · not connected 17% |
|
| GNDpin 7 | Connected to: GND 83% · a signal 17% | — |
| 3Ypin 8 | Connected to: A connector 33% · not connected 17% |
|
| 3Bpin 10 | Connected to: MCP23017-E/SO 33% · not connected 17% |
|
| 4Ypin 11 | Connected to: Signal 83% · not connected 17% |
|
| 4Bpin 13 | Connected to: MCP23017-E/SO 33% · not connected 17% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ArmRobotBoardTeensy by 01binary, MSAP-2-production by mehrantsi, Bms by IllinoisRoboticsInSpace and TC IO REVC by hankenken.
The SN74HC08DR in open source designs
The gallery holds 20 open source boards using the SN74HC08DR from 7 GitHub repositories; a typical one measures about 290 × 248.8 mm and carries around 157 components.
60% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is LegRobotBoardTeensy by 01binary.
Parts used alongside the SN74HC08DR
Microcontrollers on boards using the SN74HC08DR
What boards using the SN74HC08DR are built for
SN74HC08DR: common questions
Where can I find a SN74HC08DR reference design?
Each of the 20 boards on this page is a real design using the SN74HC08DR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the SN74HC08DR 2Y pin?
The 2Y pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the SN74HC08DR.
What resistor goes on the SN74HC08DR 3Y pin?
The 3Y pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the SN74HC08DR.
What resistor goes on the SN74HC08DR 4Y pin?
The 4Y pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the SN74HC08DR.
What parts are used alongside the SN74HC08DR?
The SN74HC74DR, AP2112K-3.3TRG1, LTV-817S, MCP23017-E/SO and SN74HC123DR appear in the most repositories here.
Which microcontrollers do boards using the SN74HC08DR use?
Most are built on AVR/Arduino (9), NXP (2) and STM32 (1).
How big is a typical board using the SN74HC08DR?
The median is 290 × 248.8 mm, and 60% are two-layer designs.
What is the most popular open source board using the SN74HC08DR?
By GitHub stars, LegRobotBoardTeensy by 01binary, with 20 stars.
Can I simulate one of these boards using the SN74HC08DR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.