11 open source boards using the SN74HC14N
Real designs built with the SN74HC14N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
24h Digital Clock
erikvanzijst
152.9 × 74.9 mm82 parts2LNo license21Vectron handheld
nickbild
273.1 × 221 mm42 parts2LNo license10ESP32
OpenSpritzer-V2
MaximeZimmermann
200 × 100 mm75 parts2LGPL-3.02ESP32
Esp32-ecu
markthebault
120 × 120 mm214 parts6LNo license0Load-UI MCU
hiramrodriguez14
85 × 90 mm102 parts4LMIT0AVR/Arduino
DMX2SGM
Gabse
66.5 × 90.9 mm32 parts2LCC-BY-NC-4.00PLL with switch
ntua-el20199
44.6 × 52.1 mm31 parts2LNo license0COMMANDS COUNTER
Iluhaprog
100 × 110 mm66 parts2LNo license0Sahs
ntua-el20199
157 × 71 mm30 parts2LNo license0Lcr addon
eulerlab
85.1 × 55.1 mm15 parts2LMIT21FLAGS REGISTER
Iluhaprog
70 × 65 mm42 parts2LNo license0
How designs wire the SN74HC14N
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the SN74HC14N connects to, and the resistors, capacitors and other passives placed on it.
- The 6Y pin is left unconnected on 7 of 9 designs (a signal on 2).
- The 1A pin has a series resistor on 5 of 9 designs, most often 1 kΩ (then 390 Ω).
- The VCC pin has a decoupling capacitor on 5 of 9 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1Apin 1 | Connected to: Signal 89% |
|
| 3Apin 5 | Connected to: Signal 56% · not connected 44% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| 4Apin 9 | Connected to: Signal 56% · not connected 44% |
|
| 6Ypin 12 | Connected to: Not connected 78% · a signal 22% | — |
| 6Apin 13 | Connected to: Signal 44% · not connected 22% · GND 22% |
|
| VCCpin 14 | Connected to: 5V 89% |
|
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 24h Digital Clock by erikvanzijst, Lcr addon by eulerlab, Vectron handheld by nickbild and OpenSpritzer-V2 by MaximeZimmermann.
The SN74HC14N in open source designs
The gallery holds 11 open source boards using the SN74HC14N from 9 GitHub repositories; a typical one measures about 100 × 90 mm and carries around 42 components.
82% are two-layer designs, the rest use four layers or more, and 27% carry an open source license.
The most starred is 24h Digital Clock by erikvanzijst.
Parts used alongside the SN74HC14N
Microcontrollers on boards using the SN74HC14N
What boards using the SN74HC14N are built for
SN74HC14N: common questions
Where can I find a SN74HC14N reference design?
Each of the 11 boards on this page is a real design using the SN74HC14N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the SN74HC14N 6Y pin connected?
The 6Y pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the SN74HC14N.
What resistor goes on the SN74HC14N 1A pin?
The 1A pin has a series resistor on 5 of 9 designs, most often 1 kΩ (then 390 Ω). Counted from the KiCad layouts of 9 open source designs using the SN74HC14N.
What decoupling capacitors do designs use on the SN74HC14N VCC pin?
The VCC pin has a decoupling capacitor on 5 of 9 designs, most often 100 nF. Counted from the KiCad layouts of 9 open source designs using the SN74HC14N.
Which microcontrollers do boards using the SN74HC14N use?
Most are built on ESP32 (2) and AVR/Arduino (1).
How big is a typical board using the SN74HC14N?
The median is 100 × 90 mm, and 82% are two-layer designs.
What is the most popular open source board using the SN74HC14N?
By GitHub stars, 24h Digital Clock by erikvanzijst, with 21 stars.
Can I simulate one of these boards using the SN74HC14N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.