7 open source boards using the SN74LVC2G07DBVR
Real designs built with the SN74LVC2G07DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
DonutDongle
svirant
42.2 × 68.1 mm40 parts2LGPL-3.016Pi hat
race-on
65 × 56.5 mm70 parts2LNo license4Microchip SAM
WiFi-Gate-Control-Board
mikelawrence
139.7 × 158.8 mm252 parts4LNo license3STM32
Fpga mocap
TobiasJaeggi
60.6 × 100 mm188 parts6LGPL-3.01STM32
Flight-Controller-V1
desanv01
104 × 104 mm310 parts6LCustom license0Controller
Iari-Lab
94 × 78 mm111 parts6LNo license26Controller
krasin
105 × 72 mm108 parts4LCERN-OHL-S-2.01
How designs wire the SN74LVC2G07DBVR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the SN74LVC2G07DBVR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF.
- The 1Y pin has a pull-up to 5V on 3 of 7 designs, most often 10 kΩ (then 3.9 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 5 | Connected to: 3.3V 100% |
|
| 1Ypin 6 | Connected to: Signal 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Controller by Iari-Lab, DonutDongle by svirant, Pi hat by race-on and WiFi-Gate-Control-Board by mikelawrence.
The SN74LVC2G07DBVR in open source designs
The gallery holds 7 open source boards using the SN74LVC2G07DBVR from 7 GitHub repositories; a typical one measures about 94 × 78 mm and carries around 111 components.
71% use four copper layers or more, and 43% carry an open source license.
The most starred is Controller by Iari-Lab.
Parts used alongside the SN74LVC2G07DBVR
Microcontrollers on boards using the SN74LVC2G07DBVR
What boards using the SN74LVC2G07DBVR are built for
SN74LVC2G07DBVR: common questions
Where can I find a SN74LVC2G07DBVR reference design?
Each of the 7 boards on this page is a real design using the SN74LVC2G07DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN74LVC2G07DBVR VCC pin?
The VCC pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the SN74LVC2G07DBVR.
What pull-up resistor is used on the SN74LVC2G07DBVR 1Y pin?
The 1Y pin has a pull-up to 5V on 3 of 7 designs, most often 10 kΩ (then 3.9 kΩ). Counted from the KiCad layouts of 7 open source designs using the SN74LVC2G07DBVR.
Which microcontrollers do boards using the SN74LVC2G07DBVR use?
Most are built on STM32 (2) and Microchip SAM (1).
How big is a typical board using the SN74LVC2G07DBVR?
The median is 94 × 78 mm, and 29% are two-layer designs.
What is the most popular open source board using the SN74LVC2G07DBVR?
By GitHub stars, Controller by Iari-Lab, with 26 stars.
Can I simulate one of these boards using the SN74LVC2G07DBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.