17 open source boards using the TAR5SxxU
Real designs built with the TAR5SxxU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
CaravelPmod
mdrobot7
66.1 × 91 mm36 parts2LNo license0Clear dev v1
efabless
76.2 × 73.8 mm84 parts2LNo license40Clear dev v1
chipfoundry
76.2 × 73.8 mm84 parts2LNo license1Clear dev v1
weyer7
76.2 × 73.8 mm84 parts2LNo license1Clear dev v1
Rimal12345
76.2 × 73.8 mm84 parts2LNo license0Fab-Drawing clear dev v1
efabless
76.2 × 73.8 mm84 parts2LNo license40Fab-Drawing clear dev v1
weyer7
76.2 × 73.8 mm84 parts2LNo license1Fab-Drawing clear dev v1
chipfoundry
76.2 × 73.8 mm84 parts2LNo license1Fab-Drawing clear dev v1
Rimal12345
76.2 × 73.8 mm84 parts2LNo license0Caravel dev v5-M.2
efabless
76.2 × 73.8 mm68 parts2LNo license40Caravel dev v5-M.2
chipfoundry
76.2 × 73.8 mm68 parts2LNo license1Caravel dev v5-M.2
weyer7
76.2 × 73.8 mm68 parts2LNo license1Caravel dev v5-M.2
Rimal12345
76.2 × 73.8 mm68 parts2LNo license0Fab-Drawing caravel dev v5-M.2
efabless
76.2 × 73.8 mm68 parts2LNo license40Fab-Drawing caravel dev v5-M.2
weyer7
76.2 × 73.8 mm68 parts2LNo license1Fab-Drawing caravel dev v5-M.2
chipfoundry
76.2 × 73.8 mm68 parts2LNo license1Fab-Drawing caravel dev v5-M.2
Rimal12345
76.2 × 73.8 mm68 parts2LNo license0
How designs wire the TAR5SxxU
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TAR5SxxU connects to, and the resistors, capacitors and other passives placed on it.
- The CONTROL pin has a pull-up to 5V on 5 of 5 designs, most often 10 kΩ.
- The NOISE pin has a capacitor to GND on 5 of 5 designs, most often 10 nF.
- The VOUT pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF.
- The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 1 µF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CONTROLpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| NOISEpin 3 | Connected to: Signal 100% |
|
| VOUTpin 4 | Connected to: 1.8V 100% |
|
| VINpin 5 | Connected to: 5V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Caravel dev v5-M.2 by efabless, Caravel dev v5-M.2 by chipfoundry, Caravel dev v5-M.2 by weyer7 and CaravelPmod by mdrobot7.
The TAR5SxxU in open source designs
The gallery holds 17 open source boards using the TAR5SxxU from 5 GitHub repositories; a typical one measures about 76.2 × 73.8 mm and carries around 68 components.
100% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is Fab-Drawing clear dev v1 by efabless.
Parts used alongside the TAR5SxxU
Microcontrollers on boards using the TAR5SxxU
What boards using the TAR5SxxU are built for
TAR5SxxU: common questions
Where can I find a TAR5SxxU reference design?
Each of the 17 boards on this page is a real design using the TAR5SxxU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TAR5SxxU CONTROL pin?
The CONTROL pin has a pull-up to 5V on 5 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the TAR5SxxU.
How is the TAR5SxxU NOISE pin connected?
The NOISE pin has a capacitor to GND on 5 of 5 designs, most often 10 nF. Counted from the KiCad layouts of 5 open source designs using the TAR5SxxU.
What decoupling capacitors do designs use on the TAR5SxxU VOUT pin?
The VOUT pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF. Counted from the KiCad layouts of 5 open source designs using the TAR5SxxU.
What parts are used alongside the TAR5SxxU?
The AZ1117CH-1.8TRG1, DS1086LU, FT232H, M.2-CONNECTOR-E and NCP1117LPST33T3G appear in the most repositories here.
Which microcontrollers do boards using the TAR5SxxU use?
Most are built on RP2040/RP2350 (1).
How big is a typical board using the TAR5SxxU?
The median is 76.2 × 73.8 mm, and 100% are two-layer designs.
What is the most popular open source board using the TAR5SxxU?
By GitHub stars, Fab-Drawing clear dev v1 by efabless, with 40 stars.
Can I simulate one of these boards using the TAR5SxxU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.