9 open source boards using the TCA6408ARSVR
Real designs built with the TCA6408ARSVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
TRNXSDR-carrier
acruxcz
91.8 × 139.8 mm702 parts6LCERN-OHL-S-2.015TI MSP430/CC
Projet Sound Bar DIY
HodearS
165.7 × 85 mm799 parts4LNo license2TI MSP430/CC
PROC091G
um-kiho
115.3 × 25.3 mm440 parts8LNo license0STM32
Falcon CAN Module
hpvdt
50 × 21 mm55 parts4LNo license0TI MSP430/CC
PROC091F
um-kiho
1.9 × 1.9 mm414 parts8LNo license0AVR/Arduino
Spar Sensor
hpvdt
40.3 × 15.8 mm25 parts2LNo license0Indicator rev 2
hpvdt
55 × 56 mm23 parts2LNo license0Aircraft Joystick Reader & Regulator - Servo
hpvdt
17 × 15.6 mm18 parts2LNo license0BesteLampe! ABL Controller Module
lenaschimmel
56.5 × 124 mm31 parts4LNo license18
How designs wire the TCA6408ARSVR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TCA6408ARSVR connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ).
- The VCCP pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
- The VCCI pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RESETpin 1 | Connected to: Signal 80% · 3.3V 20% |
|
| P0pin 2 | Connected to: A connector 40% |
|
| P1pin 3 | Connected to: A connector 40% |
|
| P3pin 5 | Connected to: A connector 40% |
|
| GNDpin 6 | Connected to: GND 100% | — |
| P4pin 7 | Connected to: A connector 40% |
|
| P5pin 8 | Connected to: Signal 80% · not connected 20% |
|
| P6pin 9 | Connected to: Signal 60% · not connected 40% |
|
| INTpin 11 | Connected to: Signal 60% · not connected 40% |
|
| SCLpin 12 | Connected to: The microcontroller 40% |
|
| SDApin 13 | Connected to: The microcontroller 40% |
|
| VCCPpin 14 | Connected to: 3.3V 80% · a signal 20% |
|
| VCCIpin 15 | Connected to: 3.3V 80% · a signal 20% |
|
| ADDRpin 16 | Connected to: GND 80% · not connected 20% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BesteLampe! ABL Controller Module by lenaschimmel, TRNXSDR-carrier by acruxcz, Projet Sound Bar DIY by HodearS and Indicator rev 2 by hpvdt.
The TCA6408ARSVR in open source designs
The gallery holds 9 open source boards using the TCA6408ARSVR from 5 GitHub repositories; a typical one measures about 55 × 25.3 mm and carries around 55 components.
67% use four copper layers or more, and 11% carry an open source license.
The most starred is BesteLampe! ABL Controller Module by lenaschimmel.
Parts used alongside the TCA6408ARSVR
Microcontrollers on boards using the TCA6408ARSVR
What boards using the TCA6408ARSVR are built for
TCA6408ARSVR: common questions
Where can I find a TCA6408ARSVR reference design?
Each of the 9 boards on this page is a real design using the TCA6408ARSVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TCA6408ARSVR SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the TCA6408ARSVR.
What pull-up resistor is used on the TCA6408ARSVR SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the TCA6408ARSVR.
What decoupling capacitors do designs use on the TCA6408ARSVR VCCP pin?
The VCCP pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the TCA6408ARSVR.
Which microcontrollers do boards using the TCA6408ARSVR use?
Most are built on TI MSP430/CC (3), STM32 (2) and AVR/Arduino (1).
How big is a typical board using the TCA6408ARSVR?
The median is 55 × 25.3 mm, and 33% are two-layer designs.
What is the most popular open source board using the TCA6408ARSVR?
By GitHub stars, BesteLampe! ABL Controller Module by lenaschimmel, with 18 stars.
Can I simulate one of these boards using the TCA6408ARSVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.