17 open source boards using the TJA1051T/3/1J
Real designs built with the TJA1051T/3/1J, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Cheap-FOCer-2
shamansystems
59.1 × 99.9 mm165 partsNo license406STM32
CawDrive
noxrick91
50 × 42 mm96 parts4LGPL-3.0107STM32
FOC
nordstream3
75.2 × 99.5 mm238 parts4LNo license80STM32
FOC KING
b264
75.2 × 99.5 mm238 parts4LNo license3ESP32
PriusG2
ksmola
147.8 × 65 mm145 parts4LNo license3STM32
ProPrj New Project 2026-07-15 23-14-34 2026-07-27
kms254
250 × 50 mm142 parts4LNo license1STM32
BMW-F20-AHU-CAN-Relay
Richard-CRT
56.7 × 45.1 mm58 parts4LNo license1- schematic only · 15 partsSTM32
BMS-6s
Manasviii15
15 partsNo license1 ESP32
N2k atom can485 hw
jtroyer76
32 × 64 mm28 parts2LCERN-OHL-S-2.00STM32
WBO
andreika-git
24.6 × 14 mm63 parts4LNo license36STM32
Board3-routed
kms254
250 × 50 mm140 parts4LNo license1STM32
NX J401 Adapter
RealtimeRoboticsGroup
119.6 × 99.2 mm127 parts4LSHL-2.11STM32
Board3-stripped
kms254
250 × 50 mm140 parts4LNo license1ESP32
Eps-8pin rev3
nathanfraske
96 × 40 mm63 parts4LApache-2.00ESP32
CEC PCIe 8-pin 3-Port Module
nathanfraske
103.4 × 56 mm54 parts4LApache-2.00Hellen1-can
rusefi
11.3 × 7 mm6 parts2LNo license0ESP32
CEC PCIe 8-pin 2-Port Module
nathanfraske
86.4 × 44 mm45 parts4LApache-2.00
How designs wire the TJA1051T/3/1J
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the TJA1051T/3/1J connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 11 of 12 designs, most often 100 nF (then 2.2 µF).
- The CANL pin has a series resistor on 9 of 12 designs, most often 120 Ω (then 100 Ω).
- The S pin is tied to GND on 10 of 12 designs (a signal on 2).
- The VIO pin has a decoupling capacitor on 8 of 12 designs, most often 100 nF (then 2.2 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| VCCpin 3 | Connected to: 5V 92% |
|
| VIOpin 5 | Connected to: 3.3V 92% |
|
| CANLpin 6 | Connected to: A connector 67% |
|
| CANHpin 7 | Connected to: A connector 67% |
|
| Spin 8 | Connected to: GND 83% · a signal 17% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Cheap-FOCer-2 by shamansystems, CawDrive by noxrick91, FOC by nordstream3 and WBO by andreika-git.
The TJA1051T/3/1J in open source designs
The gallery holds 17 open source boards using the TJA1051T/3/1J from 13 GitHub repositories; a typical one measures about 80.8 × 50 mm and carries around 96 components.
87% use four copper layers or more, and 29% carry an open source license.
The most starred is Cheap-FOCer-2 by shamansystems.
Parts used alongside the TJA1051T/3/1J
What boards using the TJA1051T/3/1J are built for
TJA1051T/3/1J: common questions
Where can I find a TJA1051T/3/1J reference design?
Each of the 17 boards on this page is a real design using the TJA1051T/3/1J. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TJA1051T/3/1J VCC pin?
The VCC pin has a decoupling capacitor on 11 of 12 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 12 open source designs using the TJA1051T/3/1J.
What resistor goes on the TJA1051T/3/1J CANL pin?
The CANL pin has a series resistor on 9 of 12 designs, most often 120 Ω (then 100 Ω). Counted from the KiCad layouts of 12 open source designs using the TJA1051T/3/1J.
How is the TJA1051T/3/1J S pin connected?
The S pin is tied to GND on 10 of 12 designs (a signal on 2). Counted from the KiCad layouts of 12 open source designs using the TJA1051T/3/1J.
What parts are used alongside the TJA1051T/3/1J?
The AMS1117-3.3, STM32F405RGT6, BMI270, IRS21867S and LM74700QDBVRQ1 appear in the most repositories here.
Which microcontrollers do boards using the TJA1051T/3/1J use?
Most are built on STM32 (11) and ESP32 (5).
How big is a typical board using the TJA1051T/3/1J?
The median is 80.8 × 50 mm, and 13% are two-layer designs.
What is the most popular open source board using the TJA1051T/3/1J?
By GitHub stars, Cheap-FOCer-2 by shamansystems, with 406 stars.
Can I simulate one of these boards using the TJA1051T/3/1J before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.