15 open source boards using the TLP291
Real designs built with the TLP291, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Doorbot
makeitlabs
65 × 56.5 mm75 parts2LNo license2STM32
Impeller18
buglalis
236.1 × 156.9 mm750 parts4LNo license0ESP32
Industrial IoT Controller
Hossam-Mamdouh
102 × 173.9 mm189 parts2LMIT0STM32
OIBUS MOSFET driver module
o16s
90.2 × 95.9 mm143 parts2LNo license001 how2make powersupply boardd like Thestf
Awattson
132.5 × 82.5 mm68 parts2LNo license0ESP32
Stencil
fujiy
44 × 40 mm54 parts2LNo license0Kicad projects
jibonaronno
74.6 × 76.8 mm47 parts2LCC0-1.0010000001
gitlunard
45.7 × 98 mm46 partsNo license0AVR/Arduino
IO NRF
crlab3
79 × 49.9 mm38 parts2LNo license0Plug in supply distributor
OUXT-Polaris
56 × 34.6 mm35 parts2LMIT0- schematic only · 80 parts
Poeset
faoziaziz
80 partsNo license0 ESP32
Driver
fujiy
45 × 40 mm46 parts2LNo license0Core2025 board ems
team-continue
70 × 40 mm22 parts2LNo license0Vbus converter mezzanine
o16s
10.9 × 29.2 mm17 parts2LNo license0AVR/Arduino
Heating controller
lucanastasio
100 × 50 mm145 parts2LNo license1
How designs wire the TLP291
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the TLP291 connects to, and the resistors, capacitors and other passives placed on it.
- The 1_1 pin has a series resistor on 10 of 12 designs, most often 100 Ω (then 4.7 kΩ).
- The 4_4 pin has a pull-up to 3.3V on 6 of 12 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1_1pin 1 | Connected to: Signal 92% |
|
| 4_4pin 4 | Connected to: The microcontroller 33% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Doorbot by makeitlabs, Heating controller by lucanastasio, 01 how2make powersupply boardd like Thestf by Awattson and Impeller18 by buglalis.
The TLP291 in open source designs
The gallery holds 15 open source boards using the TLP291 from 13 GitHub repositories; a typical one measures about 72.3 × 53.3 mm and carries around 54 components.
92% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Doorbot by makeitlabs.
Parts used alongside the TLP291
Microcontrollers on boards using the TLP291
What boards using the TLP291 are built for
TLP291: common questions
Where can I find a TLP291 reference design?
Each of the 15 boards on this page is a real design using the TLP291. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLP291 1_1 pin?
The 1_1 pin has a series resistor on 10 of 12 designs, most often 100 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 12 open source designs using the TLP291.
What pull-up resistor is used on the TLP291 4_4 pin?
The 4_4 pin has a pull-up to 3.3V on 6 of 12 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 12 open source designs using the TLP291.
Which microcontrollers do boards using the TLP291 use?
Most are built on AVR/Arduino (3), ESP32 (3) and STM32 (2).
How big is a typical board using the TLP291?
The median is 72.3 × 53.3 mm, and 92% are two-layer designs.
What is the most popular open source board using the TLP291?
By GitHub stars, Doorbot by makeitlabs, with 2 stars.
Can I simulate one of these boards using the TLP291 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.