8 open source boards using the TLP293
Real designs built with the TLP293, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Fpga mocap
TobiasJaeggi
60.6 × 100 mm188 parts6LGPL-3.01ESP32
Bridge writer
tmcit-ararobo-2026a
100 × 65 mm226 parts4LMIT0Raspberry Pi
ORCA CORE
UEC-RMF-Rescue
99 × 94 mm182 parts2LNo license0STM32
Esc control hub
tmcit-ararobo-2026a
50 × 90 mm130 parts4LMIT0Mesa-7i96s-P1-Port-BOB
Szymon423
52.5 × 98 mm104 parts2LCC-BY-4.00USB JST-XH Converter
issaimaru
55.9 × 35.9 mm44 parts2LApache-2.09Raspberry Pi
ORCA CORE A
UEC-RMF-Rescue
99 × 99 mm96 parts2LNo license0ORCA CORE B
UEC-RMF-Rescue
99 × 94 mm86 parts2LNo license0
How designs wire the TLP293
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TLP293 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 4 has a pull-up to 5V on 5 of 6 designs, most often 10 kΩ (then 15 kΩ).
- Pin 2 is tied to GND on 4 of 6 designs (a signal on 2).
- Pin 1 has a pull-up to VCC on 3 of 6 designs, most often 10 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: GND 67% · a signal 33% | — |
| Pin 4 | Connected to: Signal 83% · 3.3V 17% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include USB JST-XH Converter by issaimaru, Fpga mocap by TobiasJaeggi, Mesa-7i96s-P1-Port-BOB by Szymon423 and Bridge writer by tmcit-ararobo-2026a.
The TLP293 in open source designs
The gallery holds 8 open source boards using the TLP293 from 6 GitHub repositories; a typical one measures about 79.8 × 94 mm and carries around 117 components.
63% are two-layer designs, the rest use four layers or more, and 63% carry an open source license.
The most starred is USB JST-XH Converter by issaimaru.
Parts used alongside the TLP293
Microcontrollers on boards using the TLP293
What boards using the TLP293 are built for
TLP293: common questions
Where can I find a TLP293 reference design?
Each of the 8 boards on this page is a real design using the TLP293. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TLP293 pin 4?
Pin 4 has a pull-up to 5V on 5 of 6 designs, most often 10 kΩ (then 15 kΩ). Counted from the KiCad layouts of 6 open source designs using the TLP293.
How is the TLP293 pin 2 connected?
Pin 2 is tied to GND on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the TLP293.
What pull-up resistor is used on the TLP293 pin 1?
Pin 1 has a pull-up to VCC on 3 of 6 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the TLP293.
Which microcontrollers do boards using the TLP293 use?
Most are built on Raspberry Pi (2), STM32 (2) and ESP32 (1).
How big is a typical board using the TLP293?
The median is 79.8 × 94 mm, and 63% are two-layer designs.
What is the most popular open source board using the TLP293?
By GitHub stars, USB JST-XH Converter by issaimaru, with 9 stars.
Can I simulate one of these boards using the TLP293 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.