6 open source boards using the TLV75801PDBVR
Real designs built with the TLV75801PDBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
BDCMotorController
nunosousa
203.5 × 90 mm313 parts4LMIT0ESP32
HX6-Miner
IsSasoriDev
170 × 115 mm258 parts6LGPL-3.00ESP32
E-Display
doug-harriman
2.5 × 2.5 mm174 parts2LMIT0ESP32
GlucoBit
jdharcourt
55 × 30.4 mm43 parts4LNo license0RP2040/RP2350
Atlas2350 connected LiPo development board
Amronos
80 × 75 mm115 parts4LApache-2.01AVR/Arduino
RotationEncoder
nunosousa
50 × 25 mm47 parts4LMIT0
How designs wire the TLV75801PDBVR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TLV75801PDBVR connects to, and the resistors, capacitors and other passives placed on it.
- The FB_4 pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ (then 100 kΩ).
- The FB_4 pin has a resistor to GND on 5 of 5 designs, most often 10 kΩ (then 20 kΩ).
- The OUT_5 pin is tied to 3.3V on 5 of 5 designs.
- The IN_1 pin is tied to 3.3V on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN_1pin 1 | Connected to: 3.3V 80% · a signal 20% | — |
| GND_2pin 2 | Connected to: GND 100% | — |
| EN_3pin 3 | Connected to: Signal 80% · 5.5V 20% |
|
| FB_4pin 4 | Connected to: Signal 100% |
|
| OUT_5pin 5 | Connected to: 3.3V 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Atlas2350 connected LiPo development board by Amronos, E-Display by doug-harriman, HX6-Miner by IsSasoriDev and GlucoBit by jdharcourt.
The TLV75801PDBVR in open source designs
The gallery holds 6 open source boards using the TLV75801PDBVR from 5 GitHub repositories; a typical one measures about 67.5 × 52.7 mm and carries around 145 components.
83% use four copper layers or more, and 83% carry an open source license.
The most starred is Atlas2350 connected LiPo development board by Amronos.
Parts used alongside the TLV75801PDBVR
Microcontrollers on boards using the TLV75801PDBVR
What boards using the TLV75801PDBVR are built for
TLV75801PDBVR: common questions
Where can I find a TLV75801PDBVR reference design?
Each of the 6 boards on this page is a real design using the TLV75801PDBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TLV75801PDBVR FB_4 pin?
The FB_4 pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 5 open source designs using the TLV75801PDBVR.
How is the TLV75801PDBVR OUT_5 pin connected?
The OUT_5 pin is tied to 3.3V on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TLV75801PDBVR.
How is the TLV75801PDBVR IN_1 pin connected?
The IN_1 pin is tied to 3.3V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TLV75801PDBVR.
Which microcontrollers do boards using the TLV75801PDBVR use?
Most are built on ESP32 (3), AVR/Arduino (2) and RP2040/RP2350 (1).
How big is a typical board using the TLV75801PDBVR?
The median is 67.5 × 52.7 mm, and 17% are two-layer designs.
What is the most popular open source board using the TLV75801PDBVR?
By GitHub stars, Atlas2350 connected LiPo development board by Amronos, with 1 stars.
Can I simulate one of these boards using the TLV75801PDBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.