10 open source boards using the TMP102
Real designs built with the TMP102, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
WormControl-Relay15x5t15-ControlBoard
makerspacelt
84 × 41 mm80 parts4LCERN-OHL-S-2.00ESP32
S3.1
puji4810
90 × 55 mm79 parts2LApache-2.00STM32
Weather
jordan336
101 × 61.4 mm64 parts2LMIT0WormControl-Relay15x5t15-PowerBoard
makerspacelt
85.5 × 86 mm44 parts2LCERN-OHL-S-2.00ESP32
Kicad automation
Polymath-AS
70 × 50 mm34 parts2LMIT0- schematic only · 14 partsSTM32
Embedded twin
FionaKP
14 partsNo license0 ESP32
Backup pre fix16
puji4810
90 × 55 mm78 parts2LApache-2.00ESP32
Backup ripped
puji4810
90 × 55 mm78 parts2LApache-2.00ESP32
S3.1-before repack
puji4810
90 × 55 mm78 parts2LApache-2.00STM32
Sense
sean618
27 × 25 mm36 parts2LMIT0
How designs wire the TMP102
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TMP102 connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 4.7 µF).
- The SCL pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The SDA pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The ALERT pin is left unconnected on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SCLpin 1 | Connected to: The microcontroller 83%, a connector 50% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| ALERTpin 3 | Connected to: Not connected 83% · a signal 17% | — |
| V+pin 5 | Connected to: 3.3V 100% |
|
| SDApin 6 | Connected to: The microcontroller 83%, a connector 50% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Weather by jordan336, WormControl-Relay15x5t15-ControlBoard by makerspacelt, WormControl-Relay15x5t15-PowerBoard by makerspacelt and Kicad automation by Polymath-AS.
The TMP102 in open source designs
The gallery holds 10 open source boards using the TMP102 from 7 GitHub repositories; a typical one measures about 90 × 55 mm and carries around 71 components.
89% are two-layer designs, the rest use four layers or more, and 90% carry an open source license.
The most starred is WormControl-Relay15x5t15-ControlBoard by makerspacelt.
Parts used alongside the TMP102
What boards using the TMP102 are built for
TMP102: common questions
Where can I find a TMP102 reference design?
Each of the 10 boards on this page is a real design using the TMP102. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TMP102 V+ pin?
The V+ pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the TMP102.
What pull-up resistor is used on the TMP102 SCL pin?
The SCL pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 6 open source designs using the TMP102.
What pull-up resistor is used on the TMP102 SDA pin?
The SDA pin has a pull-up to 3.3V on 5 of 6 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 6 open source designs using the TMP102.
Which microcontrollers do boards using the TMP102 use?
Most are built on ESP32 (6) and STM32 (3).
How big is a typical board using the TMP102?
The median is 90 × 55 mm, and 89% are two-layer designs.
What is the most popular open source board using the TMP102?
By GitHub stars, WormControl-Relay15x5t15-ControlBoard by makerspacelt, with 0 stars.
Can I simulate one of these boards using the TMP102 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.