6 open source boards using the TPS2113APW
Real designs built with the TPS2113APW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Epaper breakout
jifanchn
100 × 45 mm98 parts4LNo license5ESP32
Hospital Bed Controller
Amaza-Ronald
109.5 × 105.7 mm106 parts4LNo license0ESP32
Epaper breakout
entozoon
100 × 45 mm98 parts4LNo license0ESP32
Epaper breakout
orgTestCodacy11KRepos110MB
100 × 45 mm98 parts4LNo license0ESP32
Epaper breakout
SkinnyGnome
100 × 45 mm98 parts4LNo license0Nordic nRF
Sharp-LV
martinberlin
69.7 × 44.7 mm50 parts4LMIT1
How designs wire the TPS2113APW
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS2113APW connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 6 of 6 designs, most often 400 Ω (then 1 kΩ).
- The OUT pin has a capacitor to GND on 6 of 6 designs, most often 10 µF (then 22 µF).
- The IN1 pin is tied to VBUS on 6 of 6 designs.
- The EN_N pin is tied to GND on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| STATpin 1 | Connected to: Not connected 67% · a signal 33% | — |
| EN_Npin 2 | Connected to: GND 83% · a signal 17% | — |
| VSNSpin 3 | Connected to: VBUS 83% · a signal 17% | — |
| ILIMpin 4 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| IN2pin 6 | Connected to: BAT+ 83% · a signal 17% | — |
| OUTpin 7 | Connected to: MCP1700-3302E_SOT23 67%, TPS651851RSLR 67%, a connector 67% · VIN 33% |
|
| IN1pin 8 | Connected to: VBUS 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Epaper breakout by jifanchn, Sharp-LV by martinberlin, Hospital Bed Controller by Amaza-Ronald and Epaper breakout by entozoon.
The TPS2113APW in open source designs
The gallery holds 6 open source boards using the TPS2113APW from 6 GitHub repositories; a typical one measures about 100 × 45 mm and carries around 98 components.
100% use four copper layers or more, and 17% carry an open source license.
The most starred is Epaper breakout by jifanchn.
Parts used alongside the TPS2113APW
Microcontrollers on boards using the TPS2113APW
What boards using the TPS2113APW are built for
TPS2113APW: common questions
Where can I find a TPS2113APW reference design?
Each of the 6 boards on this page is a real design using the TPS2113APW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2113APW ILIM pin?
The ILIM pin has a resistor to GND on 6 of 6 designs, most often 400 Ω (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2113APW.
How is the TPS2113APW OUT pin connected?
The OUT pin has a capacitor to GND on 6 of 6 designs, most often 10 µF (then 22 µF). Counted from the KiCad layouts of 6 open source designs using the TPS2113APW.
How is the TPS2113APW IN1 pin connected?
The IN1 pin is tied to VBUS on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TPS2113APW.
What parts are used alongside the TPS2113APW?
The MCP1700-3302E_SOT23, CH340C, ED060XC5, ESP32-WROVER and PCA9535PW appear in the most repositories here.
Which microcontrollers do boards using the TPS2113APW use?
Most are built on ESP32 (5) and Nordic nRF (1).
How big is a typical board using the TPS2113APW?
The median is 100 × 45 mm, and 0% are two-layer designs.
What is the most popular open source board using the TPS2113APW?
By GitHub stars, Epaper breakout by jifanchn, with 5 stars.
Can I simulate one of these boards using the TPS2113APW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.