7 open source boards using the TPS2553DBVR-1
Real designs built with the TPS2553DBVR-1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Letsupuri 2024 power
Pekaso
90 × 29 mm55 parts2LNo license11STM32
Bldc esc
EwoudVV
544 × 768 mm421 parts4LNo license1ESP32
Assembly preview
ripclap
110 × 96 mm423 parts6LCERN-OHL-P-2.00STM32
Keel
BisocMOrg
106 × 150 mm147 parts6LMIT0ESP32
TiltBox
Tom-Michiels
78 × 78 mm136 parts4LNo license0RP2040/RP2350
Totem trackpoint
DhruvBhatia0
258.8 × 94.4 mm131 parts4LCERN-OHL-P-2.00ESP32
Carrier
ripclap
110 × 96 mm423 parts6LCERN-OHL-P-2.00
How designs wire the TPS2553DBVR-1
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS2553DBVR-1 connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 5 of 6 designs, most often 24 kΩ (then 52.3 kΩ).
- The IN pin is tied to 5V on 4 of 6 designs (a signal on 2).
- The FAULT pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| INpin 1 | Connected to: 5V 67% · a signal 33% | — |
| GNDpin 2 | Connected to: GND 100% | — |
| ENpin 3 | Connected to: The microcontroller 33% · VBUS_L 33% |
|
| FAULTpin 4 | Connected to: The microcontroller 50% · not connected 17% |
|
| ILIMpin 5 | Connected to: Signal 83% · 5V 17% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Letsupuri 2024 power by Pekaso, Bldc esc by EwoudVV, Keel by BisocMOrg and Totem trackpoint by DhruvBhatia0.
The TPS2553DBVR-1 in open source designs
The gallery holds 7 open source boards using the TPS2553DBVR-1 from 6 GitHub repositories; a typical one measures about 110 × 96 mm and carries around 147 components.
86% use four copper layers or more, and 57% carry an open source license.
The most starred is Letsupuri 2024 power by Pekaso.
Parts used alongside the TPS2553DBVR-1
Microcontrollers on boards using the TPS2553DBVR-1
What boards using the TPS2553DBVR-1 are built for
TPS2553DBVR-1: common questions
Where can I find a TPS2553DBVR-1 reference design?
Each of the 7 boards on this page is a real design using the TPS2553DBVR-1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2553DBVR-1 ILIM pin?
The ILIM pin has a resistor to GND on 5 of 6 designs, most often 24 kΩ (then 52.3 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2553DBVR-1.
How is the TPS2553DBVR-1 IN pin connected?
The IN pin is tied to 5V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the TPS2553DBVR-1.
What pull-up resistor is used on the TPS2553DBVR-1 FAULT pin?
The FAULT pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the TPS2553DBVR-1.
Which microcontrollers do boards using the TPS2553DBVR-1 use?
Most are built on ESP32 (3), STM32 (2) and RP2040/RP2350 (1).
How big is a typical board using the TPS2553DBVR-1?
The median is 110 × 96 mm, and 14% are two-layer designs.
What is the most popular open source board using the TPS2553DBVR-1?
By GitHub stars, Letsupuri 2024 power by Pekaso, with 11 stars.
Can I simulate one of these boards using the TPS2553DBVR-1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.