7 open source boards using the TPS56339DDCR
Real designs built with the TPS56339DDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
- schematic only · 87 partsESP32
Antenny
RedBalloonShenanigans
87 partsNo license164 STM32
UPS-2 PowerSupply HW
ECOM-Engineering
65 × 56.5 mm59 parts2LCustom license2STM32
Satnogs comms
PeakSat
90.2 × 95.9 mm273 parts6LCERN-OHL-1.21STM32
YTAR
Zychlix
50 × 50 mm180 parts6LNo license0Quack core
HeyPCB
101 × 51.5 mm126 parts4LCERN-OHL-S-2.00Iris brainstem
HeyPCB
64 × 80 mm85 parts4LCERN-OHL-S-2.00Quack face
HeyPCB
128 × 51.4 mm47 parts4LCERN-OHL-S-2.00
How designs wire the TPS56339DDCR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS56339DDCR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 6 of 6 designs, most often 5.6 µH (then 4.7 µH).
- The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 10 µF (then 100 nF).
- The FB pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ.
- The SW pin has a series capacitor on 5 of 6 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 100% |
|
| VINpin 3 | Connected to: VIN_X 67% · a signal 33% |
|
| FBpin 4 | Connected to: Signal 100% |
|
| ENpin 5 | Connected to: Not connected 67% · a signal 33% | — |
| BOOTpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include UPS-2 PowerSupply HW by ECOM-Engineering, Satnogs comms by PeakSat, Iris brainstem by HeyPCB and Quack core by HeyPCB.
The TPS56339DDCR in open source designs
The gallery holds 7 open source boards using the TPS56339DDCR from 7 GitHub repositories; a typical one measures about 77.6 × 54 mm and carries around 87 components.
83% use four copper layers or more, and 57% carry an open source license.
The most starred is Antenny by RedBalloonShenanigans.
Parts used alongside the TPS56339DDCR
What boards using the TPS56339DDCR are built for
TPS56339DDCR: common questions
Where can I find a TPS56339DDCR reference design?
Each of the 7 boards on this page is a real design using the TPS56339DDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS56339DDCR SW pin connected?
The SW pin has a inductor on 6 of 6 designs, most often 5.6 µH (then 4.7 µH). Counted from the KiCad layouts of 6 open source designs using the TPS56339DDCR.
What decoupling capacitors do designs use on the TPS56339DDCR VIN pin?
The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the TPS56339DDCR.
What resistor goes on the TPS56339DDCR FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the TPS56339DDCR.
What parts are used alongside the TPS56339DDCR?
The INA226AIDGSR, MAX98357AETE+T, SN74LVC1G125DBVR, SN74LVC1G126DBVR and XC6206P332MR-G appear in the most repositories here.
Which microcontrollers do boards using the TPS56339DDCR use?
Most are built on STM32 (3) and ESP32 (1).
How big is a typical board using the TPS56339DDCR?
The median is 77.6 × 54 mm, and 17% are two-layer designs.
What is the most popular open source board using the TPS56339DDCR?
By GitHub stars, Antenny by RedBalloonShenanigans, with 164 stars.
Can I simulate one of these boards using the TPS56339DDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.